ATM-FORUM-M4-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, OBJECT-IDENTITY, Counter32, Integer32, IpAddress, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString, AutonomousType, RowStatus, TestAndIncr, RowPointer, TruthValue, TimeStamp, DateAndTime, TimeInterval FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex, OwnerString FROM IF-MIB atmForum FROM ATM-FORUM-MIB atmVplEntry, atmVclEntry, atmVpCrossConnectEntry, atmVcCrossConnectEntry, atmVplVpi, atmVclVpi, atmVclVci, atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi, atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci FROM ATM-MIB entPhysicalIndex, entPhysicalClass, entPhysicalContainedIn, entPhysicalParentRelPos FROM ENTITY-MIB hrSWInstalledIndex, hrSWInstalledName FROM HOST-RESOURCES-MIB; atmfM4MIB MODULE-IDENTITY LAST-UPDATED "9701210000Z" ORGANIZATION "ATM Forum" CONTACT-INFO " Andrew G. Malis Postal: Ascend Communications, Inc. 5 Carlisle Road Westford MA 01886 USA Tel: +1 508 952 7414 Fax: +1 508 392 9250 E-Mail: malis@ascend.com" DESCRIPTION "This MIB module is the SNMP version of the ATM Forum's M4 interface (network element view)." ::= { atmForum yyy } atmfM4MIBObjects OBJECT IDENTIFIER ::= { atmfM4MIB 1 } atmfM4MIBTraps OBJECT IDENTIFIER ::= { atmfM4MIB 2 } atmfM4MIBCompliance OBJECT IDENTIFIER ::= { atmfM4MIB 3 } -- This MIB module consists of the following groups: -- (1) ATM NE High-Level Objects -- (2) Interfaces: Physical Path Termination Point Table -- (3) TC Adaptor Table -- (4) ATM Cell Layer Interface Table -- (5) VPL Termination Point Table Extensions -- (6) VCL Termination Point Table Extensions -- (7) VP Cross-Connect Table Extensions -- (8) VC Cross-Connect Table Extensions -- (9) VP 'next VPI' Table -- (10) VC 'next VCI' Table -- (11) ATM Cell Protocol Monitoring Current Data Table -- (12) ATM Cell Protocol Monitoring History Data Table -- (13) ATM Cell Protocol Monitoring Error Log Table -- (14) TC Adaptor Protocol Monitoring Current Data Table -- (15) TC Adaptor Protocol Monitoring History Data Table -- (16) VPL UPC/NPC Disagreement Monitoring Current Data Table -- (17) VPL UPC/NPC Disagreement Monitoring History Data Table -- (18) VCL UPC/NPC Disagreement Monitoring Current Data Table -- (19) VCL UPC/NPC Disagreement Monitoring History Data Table -- (20) OAM Loopback Test Definitions -- (21) VPL/VPC Termination Point Test Table -- (22) VCL/VCC Termination Point Test Table -- (23) Equipment Table extension -- (24) Equipment Holder Table extension -- (25) Plug-In Unit Table extension -- (26) Hardware Unit/Running Software Relationship Table -- (27) Hardware Unit/Installed Software Relationship Table -- (28) Alarm Forwarding Discriminator Table -- (29) Trap Log Table -- (30) Trap Log Entry Table -- (31) Alarm Trap Log Entry Table extension -- (32) Notifications (traps) -- (33) Conformance statements -- ATM Forum M4 ATM network element (NE) high-level objects atmfM4NeVendor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor of the ATM network element." ::= { atmfM4MIBObjects 1 } atmfM4NeVersion OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the ATM network element." ::= { atmfM4MIBObjects 2 } atmfM4NeStartTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time at which the agent was last started; in other words, the time at which sysUpTime was zero." ::= { atmfM4MIBObjects 3 } atmfM4NeAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for the ATM network element." DEFVAL { 0 } ::= { atmfM4MIBObjects 4 } atmfM4NeSuppressZeroStats OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "When the value of this object is true, no entry will be created in any of the the historical statistics tables for intervals in which all counts are zero." DEFVAL { true } ::= { atmfM4MIBObjects 5 } -- ATM Forum M4 Interface Configuration Table Extensions -- Physical Path Termination Point Layer atmfM4PhysPathTpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4PhysPathTpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the physical path termination point." ::= { atmfM4MIBObjects 6 } atmfM4PhysPathTpEntry OBJECT-TYPE SYNTAX AtmfM4PhysPathTpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Columns conceptually added to the interface table entry for an ATM interface to model the physical path termination point. The row of the interface table modeling this object should also include columns for the TC Adaptor object and the ATM interface table defined in RFC 1695. The interface table entry for the physical path TP fields of an ATM interface are set up without management system control (or else that setup is outside the scope of M4)." INDEX { ifIndex } ::= { atmfM4PhysPathTpTable 1 } AtmfM4PhysPathTpEntry ::= SEQUENCE { atmfM4PhysPathTpHwUnitIndex Integer32, atmfM4PhysPathTpPortID Integer32, atmfM4PhysPathTpAlarmSeverityIndex Integer32 } atmfM4PhysPathTpHwUnitIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the index of the entry in the entPhysicalTable that represents the device (i.e., card) on which the physical path terminates." ::= { atmfM4PhysPathTpEntry 1 } atmfM4PhysPathTpPortID OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the port (within the card identified by the hardware unit index) on which the physical path terminates." ::= { atmfM4PhysPathTpEntry 2 } atmfM4PhysPathTpAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the index of the entry in the communications alarm severity profile table that should be used." DEFVAL { 0 } ::= { atmfM4PhysPathTpEntry 3 } -- ATM Forum M4 Interface Configuration Table Extensions -- TC Adaptor Layer atmfM4TcAdaptorTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4TcAdaptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the TC Adaptor." ::= { atmfM4MIBObjects 7 } atmfM4TcAdaptorEntry OBJECT-TYPE SYNTAX AtmfM4TcAdaptorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Columns conceptually added to the interface table entry for an ATM interface to model the TC Adaptor. The row of the interface table modeling this object should also include columns for the physical path TP and the ATM interface table defined in RFC 1695. The interface table entry for the TC Adaptor fields of an ATM interface are set up without management system control (or else that setup is outside the scope of M4)." INDEX { ifIndex } ::= { atmfM4TcAdaptorTable 1 } AtmfM4TcAdaptorEntry ::= SEQUENCE { atmfM4TcACellScrambling TruthValue, atmfM4TcAlarmSeverityIndex Integer32 } atmfM4TcACellScrambling OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This attribute is used by the management system to activate and deactivate the ATM cell scrambling function. When the value of this attribute is TRUE, cell scrambling on the interface is activated. This attribute shall be present only for interfaces that support the deactivation of cell scrambling. The ATM Forum UNI specification requires cell scrambling for ATM/SONET interfaces but allows cell scrambling to be controlled (i.e., turned on and off) for ATM/DS3 interfaces." DEFVAL { true } ::= { atmfM4TcAdaptorEntry 1 } atmfM4TcAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the index of the entry in the communications alarm severity profile table that should be used." DEFVAL { 0 } ::= { atmfM4TcAdaptorEntry 2 } -- ATM Forum M4 Interface Configuration Table Extensions -- ATM Cell Layer atmfM4AtmLayerTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4AtmLayerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the ATM cell layer." ::= { atmfM4MIBObjects 8 } atmfM4AtmLayerEntry OBJECT-TYPE SYNTAX AtmfM4AtmLayerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Columns conceptually added to the interface table entry for an ATM interface to model the ATM cell layer. The row of the interface table modeling this object should also include columns for the physical path TP and TC Adaptor object, as well as the ATM interface table defined in RFC 1695. The default configuration of an entry in this table is used whenever the entries for the physical path TP, etc., are created. The management system configures a UNI, B-ICI, or B-ISSI on the interface by first modifying the atmfM4IfType column (this can be done in the same SNMP set-request that sets up the other necessary variables." INDEX { ifIndex } ::= { atmfM4AtmLayerTable 1 } AtmfM4AtmLayerEntry ::= SEQUENCE { atmfM4IfType INTEGER, atmfM4IfLoopbackLocationCode Integer32, atmfM4IfSubscriberAddress DisplayString, atmfM4IfPreferredCarrier DisplayString, atmfM4IfFarEndCarrierNetwork DisplayString } atmfM4IfType OBJECT-TYPE SYNTAX INTEGER { none(0), uni(1), bici(2), bissi(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the type of ATM cell-layer interface defined on the physical path termination point modeled by this entry in the interface table." DEFVAL { none } ::= { atmfM4AtmLayerEntry 1 } atmfM4IfLoopbackLocationCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the code that shall exist in incoming OAM Loopback cells that are to be looped back at this interface. A value of zero shall indicate that the management system has not set any loopback location code for this interface. Therefore, zero should not be used as the actual loopback location code for any interface. This object shall be present only for table entries that represent an actual ATM cell layer interface (i.e., the atmM4IfType is not none(0))." DEFVAL { 0 } ::= { atmfM4AtmLayerEntry 2 } atmfM4IfSubscriberAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the address or newline-delimited list of addresses assigned to the UNI. This object shall be present only for table entries that represent an UNI interface." DEFVAL { "" } ::= { atmfM4AtmLayerEntry 3 } atmfM4IfPreferredCarrier OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the name of the default carrier to use when one is not explicitly identified in the call set-up message. This object shall be present only for table entries that represent an UNI interface and only when SVC services are supported." DEFVAL { "" } ::= { atmfM4AtmLayerEntry 4 } atmfM4IfFarEndCarrierNetwork OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies the adjacent carrier to which the B-ICI transmission path is connected. This object shall be present only for table entries that represent an B-ICI interface and only when SVC services are supported." DEFVAL { "" } ::= { atmfM4AtmLayerEntry 5 } -- ATM Forum M4 VPL Termination Point Configuration Table Extensions atmfM4VplTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VPL Termination Point Configuration table extensions. This table augments the VPL configuration table in RFC 1695." ::= { atmfM4MIBObjects 9 } atmfM4VplEntry OBJECT-TYPE SYNTAX AtmfM4VplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for the VPL configuration table entry." AUGMENTS { atmVplEntry } ::= { atmfM4VplTable 1 } AtmfM4VplEntry ::= SEQUENCE { atmfM4VplSegEndPt TruthValue } atmfM4VplSegEndPt OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the VPL termination point is a segment end-point." ::= { atmfM4VplEntry 1 } -- ATM Forum M4 VCL Termination Point Configuration Table Extensions atmfM4VclTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VCL Termination Point Configuration table extensions. This table augments the VCL configuration table in RFC 1695." ::= { atmfM4MIBObjects 10 } atmfM4VclEntry OBJECT-TYPE SYNTAX AtmfM4VclEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for the VCL configuration table entry." AUGMENTS { atmVclEntry } ::= { atmfM4VclTable 1 } AtmfM4VclEntry ::= SEQUENCE { atmfM4VclSegEndPt TruthValue } atmfM4VclSegEndPt OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the VCL termination point is a segment end-point." ::= { atmfM4VclEntry 1 } -- ATM Forum M4 VP Cross-Connect Table Extensions atmfM4VpXConnTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VpXConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VP Cross-Connect Configuration table extensions. This table augments the VP Cross-Connect configuration table in RFC 1695." ::= { atmfM4MIBObjects 11 } atmfM4VpXConnEntry OBJECT-TYPE SYNTAX AtmfM4VpXConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for the VP Cross-Connect table entry." AUGMENTS { atmVpCrossConnectEntry } ::= { atmfM4VpXConnTable 1 } AtmfM4VpXConnEntry ::= SEQUENCE { atmfM4VpXConnRecover TruthValue } atmfM4VpXConnRecover OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If FALSE, this cross-connection will be removed on failure." ::= { atmfM4VpXConnEntry 1 } -- ATM Forum M4 VC Cross-Connect Table Extensions atmfM4VcXConnTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VcXConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VC Cross-Connect Configuration table extensions. This table augments the VC Cross-Connect configuration table in RFC 1695." ::= { atmfM4MIBObjects 12 } atmfM4VcXConnEntry OBJECT-TYPE SYNTAX AtmfM4VcXConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional columns for the VC Cross-Connect table entry." AUGMENTS { atmVcCrossConnectEntry } ::= { atmfM4VcXConnTable 1 } AtmfM4VcXConnEntry ::= SEQUENCE { atmfM4VcXConnRecover TruthValue } atmfM4VcXConnRecover OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If FALSE, this cross-connection will be removed on failure." ::= { atmfM4VcXConnEntry 1 } -- ATM Forum M4 VP "Next VPI" Table atmfM4VpNextVpiTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VpNextVpiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VP Next-VPI value table. This optional table supplied unused VPI values for use in creating entries in the atmVplTable." ::= { atmfM4MIBObjects 13 } atmfM4VpNextVpiEntry OBJECT-TYPE SYNTAX AtmfM4VpNextVpiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the 'next' VPI value available for a given ATM interface. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it." INDEX { ifIndex } ::= { atmfM4VpNextVpiTable 1 } AtmfM4VpNextVpiEntry ::= SEQUENCE { atmfM4VpNextVpiValue INTEGER } atmfM4VpNextVpiValue OBJECT-TYPE SYNTAX INTEGER (-1..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for atmVplVpi when creating entries in the atmVplTable. The value -1 indicates that no unassigned entries are available. To obtain the atmVplVpi value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1)." ::= { atmfM4VpNextVpiEntry 1 } -- ATM Forum M4 VC "Next VCI" Table atmfM4VcNextVciTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VcNextVciEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VC Next-VCI value table. This optional table supplied unused VCI values for use in creating entries in the atmVclTable." ::= { atmfM4MIBObjects 14 } atmfM4VcNextVciEntry OBJECT-TYPE SYNTAX AtmfM4VcNextVciEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents the 'next' VCI value available for a given ATM interface. Each VPL Termination Point automatically has an entry in this table associated with it." INDEX { ifIndex, atmVplVpi } ::= { atmfM4VcNextVciTable 1 } AtmfM4VcNextVciEntry ::= SEQUENCE { atmfM4VcNextVciValue INTEGER } atmfM4VcNextVciValue OBJECT-TYPE SYNTAX INTEGER (-1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for atmVclVci when creating entries in the atmVclTable. The value -1 indicates that no unassigned entries are available. To obtain the atmVclVci value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1)." ::= { atmfM4VcNextVciEntry 1 } -- ATM Cell Protocol Monitoring Current Data (per interface) atmfM4CellProtoCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4CellProtoCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring Current Data table. This table maintains per-interface statistics for the fifteen-minute interval currently being collected." ::= { atmfM4MIBObjects 15 } atmfM4CellProtoCurrEntry OBJECT-TYPE SYNTAX AtmfM4CellProtoCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Cell Protocol Monitoring Current Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it." INDEX { ifIndex } ::= { atmfM4CellProtoCurrTable 1 } AtmfM4CellProtoCurrEntry ::= SEQUENCE { atmfM4CellProtoCurrSuspect TruthValue, atmfM4CellProtoCurrElapsedTime TimeInterval, atmfM4CellProtoCurrSupprIntvls Counter32, atmfM4CellProtoCurrProtoErrors Counter32, atmfM4CellProtoCurrInOAMCells Counter32 } atmfM4CellProtoCurrSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4CellProtoCurrEntry 1 } atmfM4CellProtoCurrElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4CellProtoCurrEntry 2 } atmfM4CellProtoCurrSupprIntvls OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4CellProtoCurrEntry 3 } atmfM4CellProtoCurrProtoErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells dropped on this interface, due to an unrecognized field or set of fields in the ATM cell header, since the start of this interval." ::= { atmfM4CellProtoCurrEntry 4 } atmfM4CellProtoCurrInOAMCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received at this interface since the start of this interval." ::= { atmfM4CellProtoCurrEntry 5 } -- ATM Cell Protocol Monitoring History Data (per interface and time -- interval) atmfM4CellProtoHistTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4CellProtoHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring History Data table. This table maintains per-interface statistics for previous fifteen-minute intervals." ::= { atmfM4MIBObjects 16 } atmfM4CellProtoHistEntry OBJECT-TYPE SYNTAX AtmfM4CellProtoHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Cell Protocol Monitoring History Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each fifteen- minute interval in which statistics are collected for it." INDEX { ifIndex, atmfM4CellProtoHistIndex } ::= { atmfM4CellProtoHistTable 1 } AtmfM4CellProtoHistEntry ::= SEQUENCE { atmfM4CellProtoHistIndex INTEGER, atmfM4CellProtoHistSuspect TruthValue, atmfM4CellProtoHistElapsedTime TimeInterval, atmfM4CellProtoHistSupprIntvls Counter32, atmfM4CellProtoHistProtoErrors Counter32, atmfM4CellProtoHistInOAMCells Counter32 } atmfM4CellProtoHistIndex OBJECT-TYPE SYNTAX INTEGER (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { atmfM4CellProtoHistEntry 1 } atmfM4CellProtoHistSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4CellProtoHistEntry 2 } atmfM4CellProtoHistElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4CellProtoHistEntry 3 } atmfM4CellProtoHistSupprIntvls OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4CellProtoHistEntry 4 } atmfM4CellProtoHistProtoErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells dropped on this interface, due to an unrecognized field or set of fields in the ATM cell header, since the start of this interval." ::= { atmfM4CellProtoHistEntry 5 } atmfM4CellProtoHistInOAMCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of OAM cells received at this interface since the start of this interval." ::= { atmfM4CellProtoHistEntry 6 } -- ATM Cell Protocol Monitoring Error Log (per interface, error code) atmfM4CellProtoErrorTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4CellProtoErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring Error Log table. This table maintains a record of the last error of each type encountered on each interface, as a result of ATM Cell Protocol Monitoring." ::= { atmfM4MIBObjects 17 } atmfM4CellProtoErrorEntry OBJECT-TYPE SYNTAX AtmfM4CellProtoErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Cell Protocol Monitoring Error Log table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each error that has occurred since agent start-up." INDEX { ifIndex, atmfM4CellProtoErrorCode } ::= { atmfM4CellProtoErrorTable 1 } AtmfM4CellProtoErrorEntry ::= SEQUENCE { atmfM4CellProtoErrorCode Integer32, atmfM4CellProtoErrorTime TimeStamp, atmfM4CellProtoErrorReason Integer32, atmfM4CellProtoErrorVpi INTEGER, atmfM4CellProtoErrorVci INTEGER } atmfM4CellProtoErrorCode OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the type of error for which this entry contains information." ::= { atmfM4CellProtoErrorEntry 1 } atmfM4CellProtoErrorTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Value of sysUpTime when the error occurred." ::= { atmfM4CellProtoErrorEntry 2 } atmfM4CellProtoErrorReason OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cell header abnormality type: the reason for discarding the ATM cell (i.e., unassigned VPI/VCI value or VPI/VCI value out of range." ::= { atmfM4CellProtoErrorEntry 3 } atmfM4CellProtoErrorVpi OBJECT-TYPE SYNTAX INTEGER (0..4096) MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI value of the discarded cell." ::= { atmfM4CellProtoErrorEntry 4 } atmfM4CellProtoErrorVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI value of the discarded cell." ::= { atmfM4CellProtoErrorEntry 5 } -- TC Adaptor Protocol Monitoring Current Data (per interface) atmfM4TcProtoCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4TcProtoCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table. This table maintains per-interface statistics for the fifteen-minute interval currently being collected." ::= { atmfM4MIBObjects 18 } atmfM4TcProtoCurrEntry OBJECT-TYPE SYNTAX AtmfM4TcProtoCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it." INDEX { ifIndex } ::= { atmfM4TcProtoCurrTable 1 } AtmfM4TcProtoCurrEntry ::= SEQUENCE { atmfM4TcProtoCurrSuspect TruthValue, atmfM4TcProtoCurrElapsedTime TimeInterval, atmfM4TcProtoCurrSupprIntvls Counter32, atmfM4TcProtoCurrDiscardHECViol Counter32 } atmfM4TcProtoCurrSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4TcProtoCurrEntry 1 } atmfM4TcProtoCurrElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4TcProtoCurrEntry 2 } atmfM4TcProtoCurrSupprIntvls OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing ATM TC Adaptor Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4TcProtoCurrEntry 3 } atmfM4TcProtoCurrDiscardHECViol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells discarded on this interface, due to an HEC violation, since the start of this interval." ::= { atmfM4TcProtoCurrEntry 4 } -- ATM TC Adaptor Protocol Monitoring History Data (per interface and -- time interval) atmfM4TcProtoHistTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4TcProtoHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 TC Adaptor Protocol Monitoring History Data table. This table maintains per-interface statistics for previous fifteen-minute intervals." ::= { atmfM4MIBObjects 19 } atmfM4TcProtoHistEntry OBJECT-TYPE SYNTAX AtmfM4TcProtoHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 TC Adaptor Protocol Monitoring History Data table. Each ATM interface (UNI, BICI, BISSI) automatically has an entry in this table associated with it for each fifteen- minute interval in which statistics are collected for it." INDEX { ifIndex, atmfM4TcProtoHistIndex } ::= { atmfM4TcProtoHistTable 1 } AtmfM4TcProtoHistEntry ::= SEQUENCE { atmfM4TcProtoHistIndex INTEGER, atmfM4TcProtoHistSuspect TruthValue, atmfM4TcProtoHistElapsedTime TimeInterval, atmfM4TcProtoHistSupprIntvls Unsigned32, atmfM4TcProtoHistDiscardHECViol Unsigned32 } atmfM4TcProtoHistIndex OBJECT-TYPE SYNTAX INTEGER (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { atmfM4TcProtoHistEntry 1 } atmfM4TcProtoHistSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4TcProtoHistEntry 2 } atmfM4TcProtoHistElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4TcProtoHistEntry 3 } atmfM4TcProtoHistSupprIntvls OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing ATM Cell Protocol Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4TcProtoHistEntry 4 } atmfM4TcProtoHistDiscardHECViol OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ATM cells discarded on this interface, due to an HEC violation, since the start of this interval." ::= { atmfM4TcProtoHistEntry 5 } -- UPC/NPC Disagreement Monitoring Current Data (per VPL -- termination point) atmfM4VpUpcNpcCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VpUpcNpcCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points. This table maintains per-TP statistics for the fifteen-minute interval currently being collected." ::= { atmfM4MIBObjects 20 } atmfM4VpUpcNpcCurrEntry OBJECT-TYPE SYNTAX AtmfM4VpUpcNpcCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points. Each VPL Termination Point automatically has an entry in this table associated with it." INDEX { ifIndex, atmVplVpi } ::= { atmfM4VpUpcNpcCurrTable 1 } AtmfM4VpUpcNpcCurrEntry ::= SEQUENCE { atmfM4VpUpcNpcCurrSuspect TruthValue, atmfM4VpUpcNpcCurrElapsedTime TimeInterval, atmfM4VpUpcNpcCurrSupprIntvls Counter32, atmfM4VpUpcNpcCurrDiscardedCells Counter32, atmfM4VpUpcNpcCurrDiscardedClp0 Counter32, atmfM4VpUpcNpcCurrPassedCells Counter32, atmfM4VpUpcNpcCurrPassedClp0 Counter32 } atmfM4VpUpcNpcCurrSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4VpUpcNpcCurrEntry 1 } atmfM4VpUpcNpcCurrElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4VpUpcNpcCurrEntry 2 } atmfM4VpUpcNpcCurrSupprIntvls OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4VpUpcNpcCurrEntry 3 } atmfM4VpUpcNpcCurrDiscardedCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VpUpcNpcCurrEntry 4 } atmfM4VpUpcNpcCurrDiscardedClp0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VpUpcNpcCurrEntry 5 } atmfM4VpUpcNpcCurrPassedCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VpUpcNpcCurrEntry 6 } atmfM4VpUpcNpcCurrPassedClp0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VpUpcNpcCurrEntry 7 } -- UPC/NPC Disagreement Monitoring History (per VPL termination -- point and time interval) atmfM4VpUpcNpcHistTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VpUpcNpcHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points. This table maintains per-interface statistics for previous fifteen-minute intervals." ::= { atmfM4MIBObjects 21 } atmfM4VpUpcNpcHistEntry OBJECT-TYPE SYNTAX AtmfM4VpUpcNpcHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points. Each VPL Termination Point automatically has an entry in this table associated with it." INDEX { ifIndex, atmVplVpi, atmfM4VpUpcNpcHistIndex } ::= { atmfM4VpUpcNpcHistTable 1 } AtmfM4VpUpcNpcHistEntry ::= SEQUENCE { atmfM4VpUpcNpcHistIndex INTEGER, atmfM4VpUpcNpcHistSuspect TruthValue, atmfM4VpUpcNpcHistElapsedTime TimeInterval, atmfM4VpUpcNpcHistSupprIntvls Unsigned32, atmfM4VpUpcNpcHistDiscardedCells Unsigned32, atmfM4VpUpcNpcHistDiscardedClp0 Unsigned32, atmfM4VpUpcNpcHistPassedCells Unsigned32, atmfM4VpUpcNpcHistPassedClp0 Unsigned32 } atmfM4VpUpcNpcHistIndex OBJECT-TYPE SYNTAX INTEGER (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { atmfM4VpUpcNpcHistEntry 1 } atmfM4VpUpcNpcHistSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4VpUpcNpcHistEntry 2 } atmfM4VpUpcNpcHistElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4VpUpcNpcHistEntry 3 } atmfM4VpUpcNpcHistSupprIntvls OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4VpUpcNpcHistEntry 4 } atmfM4VpUpcNpcHistDiscardedCells OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VpUpcNpcHistEntry 5 } atmfM4VpUpcNpcHistDiscardedClp0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VpUpcNpcHistEntry 6 } atmfM4VpUpcNpcHistPassedCells OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VpUpcNpcHistEntry 7 } atmfM4VpUpcNpcHistPassedClp0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VpUpcNpcHistEntry 8 } -- UPC/NPC Disagreement Monitoring Current Data (per VCL -- termination point) atmfM4VcUpcNpcCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VcUpcNpcCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points. This table maintains per-TP statistics for the fifteen-minute interval currently being collected." ::= { atmfM4MIBObjects 22 } atmfM4VcUpcNpcCurrEntry OBJECT-TYPE SYNTAX AtmfM4VcUpcNpcCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points. Each VCL Termination Point automatically has an entry in this table associated with it." INDEX { ifIndex, atmVclVpi, atmVclVci } ::= { atmfM4VcUpcNpcCurrTable 1 } AtmfM4VcUpcNpcCurrEntry ::= SEQUENCE { atmfM4VcUpcNpcCurrSuspect TruthValue, atmfM4VcUpcNpcCurrElapsedTime TimeInterval, atmfM4VcUpcNpcCurrSupprIntvls Counter32, atmfM4VcUpcNpcCurrDiscardedCells Counter32, atmfM4VcUpcNpcCurrDiscardedClp0 Counter32, atmfM4VcUpcNpcCurrPassedCells Counter32, atmfM4VcUpcNpcCurrPassedClp0 Counter32 } atmfM4VcUpcNpcCurrSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4VcUpcNpcCurrEntry 1 } atmfM4VcUpcNpcCurrElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4VcUpcNpcCurrEntry 2 } atmfM4VcUpcNpcCurrSupprIntvls OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4VcUpcNpcCurrEntry 3 } atmfM4VcUpcNpcCurrDiscardedCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VcUpcNpcCurrEntry 4 } atmfM4VcUpcNpcCurrDiscardedClp0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VcUpcNpcCurrEntry 5 } atmfM4VcUpcNpcCurrPassedCells OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VcUpcNpcCurrEntry 6 } atmfM4VcUpcNpcCurrPassedClp0 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VcUpcNpcCurrEntry 7 } -- UPC/NPC Disagreement Monitoring History (per VCL termination -- point and time interval) atmfM4VcUpcNpcHistTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VcUpcNpcHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points. This table maintains per-interface statistics for previous fifteen-minute intervals." ::= { atmfM4MIBObjects 23 } atmfM4VcUpcNpcHistEntry OBJECT-TYPE SYNTAX AtmfM4VcUpcNpcHistEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points. Each VCL Termination Point automatically has an entry in this table associated with it." INDEX { ifIndex, atmVclVpi, atmVclVci, atmfM4VcUpcNpcHistIndex } ::= { atmfM4VcUpcNpcHistTable 1 } AtmfM4VcUpcNpcHistEntry ::= SEQUENCE { atmfM4VcUpcNpcHistIndex INTEGER, atmfM4VcUpcNpcHistSuspect TruthValue, atmfM4VcUpcNpcHistElapsedTime TimeInterval, atmfM4VcUpcNpcHistSupprIntvls Unsigned32, atmfM4VcUpcNpcHistDiscardedCells Unsigned32, atmfM4VcUpcNpcHistDiscardedClp0 Unsigned32, atmfM4VcUpcNpcHistPassedCells Unsigned32, atmfM4VcUpcNpcHistPassedClp0 Unsigned32 } atmfM4VcUpcNpcHistIndex OBJECT-TYPE SYNTAX INTEGER (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number between 1 and 96, which identifies the interval for which the set of statistics in this entry was collected. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { atmfM4VcUpcNpcHistEntry 1 } atmfM4VcUpcNpcHistSuspect OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, the statistics in this entry may be unreliable." ::= { atmfM4VcUpcNpcHistEntry 2 } atmfM4VcUpcNpcHistElapsedTime OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "Amount of time, measured in units of 0.01 second, that statistics for this entry (the current interval) have been counted." ::= { atmfM4VcUpcNpcHistEntry 3 } atmfM4VcUpcNpcHistSupprIntvls OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is non-zero only if the ATM NE is suppressing UPC/NPC Disagreement Monitoring History Data entry creation when the current interval terminates with 'all-zeroes' performance measurements." ::= { atmfM4VcUpcNpcHistEntry 4 } atmfM4VcUpcNpcHistDiscardedCells OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VcUpcNpcHistEntry 5 } atmfM4VcUpcNpcHistDiscardedClp0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of discarded cells due to CLP=0 only UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VcUpcNpcHistEntry 6 } atmfM4VcUpcNpcHistPassedCells OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the combined CLP=0 and CLP=1 UPC/NPC policing." ::= { atmfM4VcUpcNpcHistEntry 7 } atmfM4VcUpcNpcHistPassedClp0 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of cells that have been successfully passed by the CLP=0 UPC/NPC policing. This object shall be present only if CLP=0 traffic is separately policed." ::= { atmfM4VcUpcNpcHistEntry 8 } -- ATM Forum M4 Test Types atmfM4TestTypes OBJECT IDENTIFIER ::= { atmfM4MIBObjects 24 } -- OAM Loopback Tests (VPL, VPC, VCL, anc VCC termination points): atmfM4TestOAMLoopbackSeg OBJECT-IDENTITY STATUS current DESCRIPTION "This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using a segment OAM cell. The test type must have appended to it a code that uniquely identifies an intermediate point responsible for looping back the cell. If this is absent, the loopback is performed at the end of the segment or connection. E.g., the OID { atmfM4TestOAMLoopbackSeg 5 } identifies that the loopback should be performed at the intermediate point labeled 5." ::= { atmfM4TestTypes 1 } atmfM4TestOAMLoopbackE2E OBJECT-IDENTITY STATUS current DESCRIPTION "This identifies an OAM Loopback Test on a VPL, VPC, VCL, or VCC termination point, using an end-to-end OAM cell." ::= { atmfM4TestTypes 2 } -- ATM Forum M4 VP Termination Point Test Table atmfM4VpTestTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VpTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VP Termination Point Test table. This table allows tests to be run on VPL and VPC termination points. The operation of this table is entirely analogous to that of the ifTestTable in RFC 1573, except that the indexes into this table are different." ::= { atmfM4MIBObjects 25 } atmfM4VpTestEntry OBJECT-TYPE SYNTAX AtmfM4VpTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for invoking tests on a VPL or VPC termination point." INDEX { ifIndex, atmVplVpi, atmfM4VpTestObject } ::= { atmfM4VpTestTable 1 } AtmfM4VpTestEntry ::= SEQUENCE { atmfM4VpTestObject INTEGER, atmfM4VpTestId TestAndIncr, atmfM4VpTestStatus INTEGER, atmfM4VpTestType AutonomousType, atmfM4VpTestResult INTEGER, atmfM4VpTestCode OBJECT IDENTIFIER, atmfM4VpTestOwner OwnerString } atmfM4VpTestObject OBJECT-TYPE SYNTAX INTEGER { vplTp(1), vpcTp(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies whether the test applies to the VPL termination point with the specified VPI, or the VPC termination point." ::= { atmfM4VpTestEntry 1 } atmfM4VpTestId OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the current invocation of the interface's test." ::= { atmfM4VpTestEntry 2 } atmfM4VpTestStatus OBJECT-TYPE SYNTAX INTEGER { notInUse(1), inUse(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether or not some manager currently has the necessary 'ownership' required to invoke a test on this interface. A write to this object is only successful when it changes its value from 'notInUse(1)' to 'inUse(2)'. After completion of a test, the agent resets the value back to 'notInUse(1)'." ::= { atmfM4VpTestEntry 3 } atmfM4VpTestType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-write STATUS current DESCRIPTION "A control variable used to start and stop operator- initiated interface tests. Most OBJECT IDENTIFIER values assigned to tests are defined elsewhere, in association with specific types of interface. However, this document assigns a value for a full- duplex loopback test, and defines the special meanings of the subject identifier: noTest OBJECT IDENTIFIER ::= { 0 0 } When the value noTest is written to this object, no action is taken unless a test is in progress, in which case the test is aborted. Writing any other value to this object is only valid when no test is currently in progress, in which case the indicated test is initiated. When read, this object always returns the most recent value that atmfM4VpTestType was set to. If it has not been set since the last initialization of the network management subsystem on the agent, a value of noTest is returned." ::= { atmfM4VpTestEntry 4 } atmfM4VpTestResult OBJECT-TYPE SYNTAX INTEGER { none(1), -- no test yet requested success(2), inProgress(3), notSupported(4), unAbleToRun(5), -- due to state of system aborted(6), failed(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the result of the most recently requested test, or the value none(1) if no tests have been requested since the last reset. Note that this facility provides no provision for saving the results of one test when starting another, as could be required if used by multiple managers concurrently." ::= { atmfM4VpTestEntry 5 } atmfM4VpTestCode OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a code which contains more specific information on the test result, for example an error-code after a failed test. Error codes and other values this object may take are specific to the type of interface and/or test. The value may have the semantics of either the AutonomousType or RowPointer textual conventions as defined in RFC 1903 [15]. The identifier: testCodeUnknown OBJECT IDENTIFIER ::= { 0 0 } is defined for use if no additional result code is available." ::= { atmfM4VpTestEntry 6 } atmfM4VpTestOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-write STATUS current DESCRIPTION "The entity which currently has the 'ownership' required to invoke a test on this interface." ::= { atmfM4VpTestEntry 7 } -- ATM Forum M4 VC Termination Point Test Table atmfM4VcTestTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4VcTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 VC Termination Point Test table. This table allows tests to be run on VCL and VCC termination points. The operation of this table is entirely analogous to that of the ifTestTable in RFC 1573, except that the indexes into this table are different." ::= { atmfM4MIBObjects 26 } atmfM4VcTestEntry OBJECT-TYPE SYNTAX AtmfM4VcTestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing objects for invoking tests on a VCL or VCC termination point." INDEX { ifIndex, atmVclVpi, atmVclVci, atmfM4VcTestObject } ::= { atmfM4VcTestTable 1 } AtmfM4VcTestEntry ::= SEQUENCE { atmfM4VcTestObject INTEGER, atmfM4VcTestId TestAndIncr, atmfM4VcTestStatus INTEGER, atmfM4VcTestType AutonomousType, atmfM4VcTestResult INTEGER, atmfM4VcTestCode OBJECT IDENTIFIER, atmfM4VcTestOwner OwnerString } atmfM4VcTestObject OBJECT-TYPE SYNTAX INTEGER { vclTp(1), vccTp(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies whether the test applies to the VCL termination point with the specified VPI and VCI values, or to the VCC termination point." ::= { atmfM4VcTestEntry 1 } atmfM4VcTestId OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the current invocation of the interface's test." ::= { atmfM4VcTestEntry 2 } atmfM4VcTestStatus OBJECT-TYPE SYNTAX INTEGER { notInUse(1), inUse(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether or not some manager currently has the necessary 'ownership' required to invoke a test on this interface. A write to this object is only successful when it changes its value from 'notInUse(1)' to 'inUse(2)'. After completion of a test, the agent resets the value back to 'notInUse(1)'." ::= { atmfM4VcTestEntry 3 } atmfM4VcTestType OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-write STATUS current DESCRIPTION "A control variable used to start and stop operator- initiated interface tests. Most OBJECT IDENTIFIER values assigned to tests are defined elsewhere, in association with specific types of interface. However, this document assigns a value for a full- duplex loopback test, and defines the special meanings of the subject identifier: noTest OBJECT IDENTIFIER ::= { 0 0 } When the value noTest is written to this object, no action is taken unless a test is in progress, in which case the test is aborted. Writing any other value to this object is only valid when no test is currently in progress, in which case the indicated test is initiated. When read, this object always returns the most recent value that atmfM4VcTestType was set to. If it has not been set since the last initialization of the network management subsystem on the agent, a value of noTest is returned." ::= { atmfM4VcTestEntry 4 } atmfM4VcTestResult OBJECT-TYPE SYNTAX INTEGER { none(1), -- no test yet requested success(2), inProgress(3), notSupported(4), unAbleToRun(5), -- due to state of system aborted(6), failed(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the result of the most recently requested test, or the value none(1) if no tests have been requested since the last reset. Note that this facility provides no provision for saving the results of one test when starting another, as could be required if used by multiple managers concurrently." ::= { atmfM4VcTestEntry 5 } atmfM4VcTestCode OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains a code which contains more specific information on the test result, for example an error-code after a failed test. Error codes and other values this object may take are specific to the type of interface and/or test. The value may have the semantics of either the AutonomousType or RowPointer textual conventions as defined in RFC 1903 [15]. The identifier: testCodeUnknown OBJECT IDENTIFIER ::= { 0 0 } is defined for use if no additional result code is available." ::= { atmfM4VcTestEntry 6 } atmfM4VcTestOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-write STATUS current DESCRIPTION "The entity which currently has the 'ownership' required to invoke a test on this termination point." ::= { atmfM4VcTestEntry 7 } -- ATM Forum M4 Equipment Table atmfM4EquipTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4EquipEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Equipment table. This table augments the physical entity table." ::= { atmfM4MIBObjects 28 } atmfM4EquipEntry OBJECT-TYPE SYNTAX AtmfM4EquipEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Equipment table. Each entry of this type represents a piece of equipment within the ATM NE that neither is nor accepts a replaceable plug- in unit." INDEX { entPhysicalIndex } ::= { atmfM4EquipTable 1 } AtmfM4EquipEntry ::= SEQUENCE { atmfM4EquipAdminStatus INTEGER, atmfM4EquipLocation DisplayString, atmfM4EquipOperStatus INTEGER, atmfM4EquipVendor DisplayString, atmfM4EquipVersion AutonomousType, atmfM4EquipUserLabel DisplayString, atmfM4EquipAlarmSeverityIndex Integer32 } atmfM4EquipAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used by the adminstrator to lock and unlock the object." ::= { atmfM4EquipEntry 1 } atmfM4EquipLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The specific or general location of the component." ::= { atmfM4EquipEntry 2 } atmfM4EquipOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attributes identifies whether or not the component is capable of performing its normal functions." ::= { atmfM4EquipEntry 3 } atmfM4EquipVendor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor of the component." ::= { atmfM4EquipEntry 4 } atmfM4EquipVersion OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the component." ::= { atmfM4EquipEntry 5 } atmfM4EquipUserLabel OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "A user-friendly name for the piece of equipment." DEFVAL { "" } ::= { atmfM4EquipEntry 6 } atmfM4EquipAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this component." DEFVAL { 0 } ::= { atmfM4EquipEntry 7 } -- ATM Forum M4 Equipment Holder Table atmfM4EquipHolderTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4EquipHolderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Equipment Holder table. This table augments the physical table." ::= { atmfM4MIBObjects 29 } atmfM4EquipHolderEntry OBJECT-TYPE SYNTAX AtmfM4EquipHolderEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Equipment Holder table. Each entry of this type represents a component within the ATM NE that accepts a replaceable plug-in unit." INDEX { entPhysicalIndex } ::= { atmfM4EquipHolderTable 1 } AtmfM4EquipHolderEntry ::= SEQUENCE { atmfM4EquipHolderType INTEGER, atmfM4EquipHolderAcceptableTypes DisplayString, atmfM4EquipHolderSlotStatus INTEGER, atmfM4EquipHolderSwLoad INTEGER } atmfM4EquipHolderType OBJECT-TYPE SYNTAX INTEGER { rack(1), shelf(2), drawer(3), slot(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the component." ::= { atmfM4EquipHolderEntry 1 } atmfM4EquipHolderAcceptableTypes OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The types of plug-in units that can be supported by the slot, separated by newline characters. This attribute shall be present only when the Equipment Holder represents a slot." ::= { atmfM4EquipHolderEntry 2 } atmfM4EquipHolderSlotStatus OBJECT-TYPE SYNTAX INTEGER { empty(1), full(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attributes identifies whether or not a plug-in unit is present in the slot. This attribute shall be present only when the Equipment Holder represents a slot." ::= { atmfM4EquipHolderEntry 3 } atmfM4EquipHolderSwLoad OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "An index into the installed software table, specifying the software that is to be loaded into the plug-in unit whenever an automatic reload of software is needed. This attribute shall be present only when the Equipment Holder represents a slot." ::= { atmfM4EquipHolderEntry 4 } -- ATM Forum M4 Plug-In Unit Table atmfM4PlugInUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4PlugInUnitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Plug-In Unittable. This table augments the physical entity table." ::= { atmfM4MIBObjects 30 } atmfM4PlugInUnitEntry OBJECT-TYPE SYNTAX AtmfM4PlugInUnitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Plug-In Unit table. Each entry of this type represents a piece of equipment within the ATM NE that is inserted into and removed from an Equipment Holder." INDEX { entPhysicalIndex } ::= { atmfM4PlugInUnitTable 1 } AtmfM4PlugInUnitEntry ::= SEQUENCE { atmfM4PlugInUnitAdminStatus INTEGER, atmfM4PlugInUnitAvailStatus INTEGER, atmfM4PlugInUnitOperStatus INTEGER, atmfM4PlugInUnitVendor DisplayString, atmfM4PlugInUnitVersion AutonomousType, atmfM4PlugInUnitAlarmSeverityIndex Integer32 } atmfM4PlugInUnitAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Used by the adminstrator to lock and unlock the object." ::= { atmfM4PlugInUnitEntry 1 } atmfM4PlugInUnitAvailStatus OBJECT-TYPE SYNTAX INTEGER { available(1), inTest(2), failed(3), powerOff(4), notInstalled(5), offLine(6), dependency(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Provides further information regarding the state of the component." ::= { atmfM4PlugInUnitEntry 2 } atmfM4PlugInUnitOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attributes identifies whether or not the component is capable of performing its normal functions." ::= { atmfM4PlugInUnitEntry 3 } atmfM4PlugInUnitVendor OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor of the component." ::= { atmfM4PlugInUnitEntry 4 } atmfM4PlugInUnitVersion OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the component." ::= { atmfM4PlugInUnitEntry 5 } atmfM4PlugInUnitAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this component." DEFVAL { 0 } ::= { atmfM4PlugInUnitEntry 6 } -- ATM Forum M4 Hardware Unit/Running Software Relationship Table atmfM4HwRunningSwTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4HwRunningSwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Hardware Unit/Running Software relationship. This table describes the software that is running on each hardware unit in the ATM NE." ::= { atmfM4MIBObjects 32 } atmfM4HwRunningSwEntry OBJECT-TYPE SYNTAX AtmfM4HwRunningSwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Hardware Unit/Running Software relationship table. Each entry of this type identifies an entry in the entPhysicalTable and one in the hrRunningSoftwareTable." INDEX { atmfM4HwRunningSwHwIndex, atmfM4HwRunningSwIndex } ::= { atmfM4HwRunningSwTable 1 } AtmfM4HwRunningSwEntry ::= SEQUENCE { atmfM4HwRunningSwHwIndex INTEGER, atmfM4HwRunningSwIndex INTEGER, atmfM4HwRunningSwSwIndex INTEGER } atmfM4HwRunningSwHwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index, in the entPhysicalTable, of the containing hardware unit in this pair." ::= { atmfM4HwRunningSwEntry 1 } atmfM4HwRunningSwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique number within the context of the containing hardware unit." ::= { atmfM4HwRunningSwEntry 2 } atmfM4HwRunningSwSwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index, in the hrRunningSwTable, of the software product represented by this entry." ::= { atmfM4HwRunningSwEntry 3 } -- ATM Forum M4 Hardware Unit/Installed Software Relationship Table atmfM4HwInstalledSwTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4HwInstalledSwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Hardware Unit/Installed Software relationship. This table describes the software that is Installed on each hardware unit in the ATM NE." ::= { atmfM4MIBObjects 33 } atmfM4HwInstalledSwEntry OBJECT-TYPE SYNTAX AtmfM4HwInstalledSwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the ATM Forum M4 Hardware Unit/Installed Software relationship table. Each entry of this type identifies an entry in the physical entity table and one in the hrInstalledSoftwareTable." INDEX { atmfM4HwInstalledSwHwIndex, atmfM4HwInstalledSwIndex } ::= { atmfM4HwInstalledSwTable 1 } AtmfM4HwInstalledSwEntry ::= SEQUENCE { atmfM4HwInstalledSwHwIndex INTEGER, atmfM4HwInstalledSwIndex INTEGER, atmfM4HwInstalledSwSwIndex INTEGER, atmfM4HwSwAlarmSeverityIndex Integer32 } atmfM4HwInstalledSwHwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index, in the entPhysical table, of the containing physical entity in this pair." ::= { atmfM4HwInstalledSwEntry 1 } atmfM4HwInstalledSwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique number within the context of the containing hardware unit." ::= { atmfM4HwInstalledSwEntry 2 } atmfM4HwInstalledSwSwIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The index, in the hrInstalledSwTable, of the software product represented by this entry." ::= { atmfM4HwInstalledSwEntry 3 } atmfM4HwSwAlarmSeverityIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "An index into the alarm severity profile table, specifying the severity assignments for M4 alarms reported for this piece of software installed on the hardware unit." DEFVAL { 0 } ::= { atmfM4HwInstalledSwEntry 4 } -- ATM Forum M4 Alarm Severity Identifier Textual Convention AtmfM4AlarmLogSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of this object identifies the severity of an alarm in the log, including 'cleared'." SYNTAX INTEGER { cleared(-1), indeterminate(0), critical(1), major(2), minor(3), warning(4) } AtmfM4AlarmSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of this object identifies the severity of an alarm that has occurred. (Note that there is no value corresponding to 'cleared'.)" SYNTAX INTEGER { indeterminate(0), critical(1), major(2), minor(3), warning(4) } -- ATM Forum M4 Alarm Severity Profile Table atmfM4AlarmSevDefault OBJECT-TYPE SYNTAX AtmfM4AlarmSeverity MAX-ACCESS read-write STATUS current DESCRIPTION "The default severity value used for new profile index/trap ID pairs that have not yet been modified. This value is also used whenever an object's alarm severity profile index is set to 0." DEFVAL { minor } ::= { atmfM4MIBObjects 34 } atmfM4AlarmSevProfileIndexNext OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for atmfM4AlarmSevProfileIndex when creating entries in the atmfM4AlarmSevProfileTable. The value -1 indicates that no unassigned entries are available. To obtain the index value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index (or -1)." ::= { atmfM4MIBObjects 35 } atmfM4AlarmSevProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4AlarmSevProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 alarm severity profile table. This table specifies which profiles exist. Creating or deleting an entry in this table automatically creates or deletes the corresponding entries in the atmfM4AlarmSeverityTable." ::= { atmfM4MIBObjects 36 } atmfM4AlarmSevProfileEntry OBJECT-TYPE SYNTAX AtmfM4AlarmSevProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A group of severities, one for each alarm type in the communications alarm group." INDEX { atmfM4AlarmSevProfileIndex } ::= { atmfM4AlarmSevProfileTable 1 } AtmfM4AlarmSevProfileEntry ::= SEQUENCE { atmfM4AlarmSevProfileIndex Integer32, atmfM4AlarmSevProfileRowStatus RowStatus } atmfM4AlarmSevProfileIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number identifying this alarm severity profile." ::= { atmfM4AlarmSevProfileEntry 1 } atmfM4AlarmSevProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to delete an existing row in the table." ::= { atmfM4AlarmSevProfileEntry 2 } -- ATM Forum M4 Alarm Severity Table atmfM4AlarmSevTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4AlarmSevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 alarm severity table. This table associates profile index and trap ID pairs with severities to be used for M4 alarm traps that have occurred. (Note that this table does not apply to cleared alarms.)" ::= { atmfM4MIBObjects 37 } atmfM4AlarmSevEntry OBJECT-TYPE SYNTAX AtmfM4AlarmSevEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table associates an alarm severity profile index/trap ID pair with a severity. Deleting a particular profile's row in the alarm severity profile table deletes all rows in this table with the same profile index. Conceptually, rows corresponding to all possible trap ID's are created in this table when a new alarm severity profile is created, but the agent will return a default value except for those few traps for which values have been set." INDEX { atmfM4AlarmSevProfileIndex, atmfM4AlarmSevTrapId } ::= { atmfM4AlarmSevTable 1 } AtmfM4AlarmSevEntry ::= SEQUENCE { atmfM4AlarmSevTrapId Integer32, atmfM4AlarmSeverity AtmfM4AlarmSeverity } atmfM4AlarmSevTrapId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ID of the trap type to which this entry applies." ::= { atmfM4AlarmSevEntry 1 } atmfM4AlarmSeverity OBJECT-TYPE SYNTAX AtmfM4AlarmSeverity MAX-ACCESS read-create STATUS current DESCRIPTION "The severity to be used for this trap type when the is selected. If no value for this object has ever been set since the corresponding profile was created, the agent should return the value of the object atmfM4AlarmSevDefault" ::= { atmfM4AlarmSevEntry 2 } -- ATM Forum M4 Alarm Forwarding Discriminator Table atmfM4ForwardAllTraps OBJECT-IDENTITY STATUS current DESCRIPTION "This is used as the value of the object atmfM4ForwardedTrapObject when traps from all objects are to be forwarded, or when there is only one object of the type that forwards the specified trap type." ::= { atmfM4MIBObjects 38 } atmfM4TrapForwardingTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4TrapForwardingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Trap forwarding discriminator table. This table specifies which traps will be sent to which management system." ::= { atmfM4MIBObjects 39 } atmfM4TrapForwardingEntry OBJECT-TYPE SYNTAX AtmfM4TrapForwardingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a group of traps to be sent to a particular IP address. A new entry must have values for all attributes that do not have default values before its RowStatus column can be set to active(1)." INDEX { atmfM4TrapForwardingIndex } ::= { atmfM4TrapForwardingTable 1 } AtmfM4TrapForwardingEntry ::= SEQUENCE { atmfM4TrapForwardingIndex Integer32, atmfM4TrapForwardingDest IpAddress, atmfM4ForwardedTrapId Integer32, atmfM4ForwardedTrapObject RowPointer, atmfM4TrapForwardingPort Integer32, atmfM4LowestForwardedSeverity AtmfM4AlarmSeverity, atmfM4ForwardedIndeterminate TruthValue, atmfM4TrapForwardingRowStatus RowStatus } atmfM4TrapForwardingIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique number identifying the table entry." ::= { atmfM4TrapForwardingEntry 1 } atmfM4TrapForwardingDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address to which traps identified by this table entry should be sent." ::= { atmfM4TrapForwardingEntry 2 } atmfM4ForwardedTrapId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The ID of the trap type to which this entry applies." ::= { atmfM4TrapForwardingEntry 3 } atmfM4ForwardedTrapObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "The object to which this entry applies. By convention, this is the name of the first object in the row in the table referenced. The special value { 0 0 } indicates that traps of this type from all objects of the type that can generate it. It should also be used when traps from the ATM NE are to be specified." ::= { atmfM4TrapForwardingEntry 4 } atmfM4TrapForwardingPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The UDP port on the specified management system to which traps identified by this entry should be sent." DEFVAL { 161 } ::= { atmfM4TrapForwardingEntry 5 } atmfM4LowestForwardedSeverity OBJECT-TYPE SYNTAX AtmfM4AlarmSeverity MAX-ACCESS read-create STATUS current DESCRIPTION "The lowest severity of traps of this type from the specified object that should be sent to this address. This object has significance only if the trap type specified has a severity associated with it" DEFVAL { minor } ::= { atmfM4TrapForwardingEntry 6 } atmfM4ForwardedIndeterminate OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When this object has the value TRUE, traps with indeterminate severity will be forwarded to the specified event. This object has significance only if the trap type specified has a severity associated with it" DEFVAL { false } ::= { atmfM4TrapForwardingEntry 7 } atmfM4TrapForwardingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to delete an existing row in the table." ::= { atmfM4TrapForwardingEntry 8 } -- ATM Forum M4 Trap Agent MIB Log Table atmfM4TrapLogTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4TrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent log table. This table defines the trap logs currently maintained by the agent. The management system creates entries in this table to specify which types of traps, from which ATM network elements, should be logged. Deleting an entry in this table deletes all entries in the corresponding log." ::= { atmfM4MIBObjects 40 } atmfM4TrapLogEntry OBJECT-TYPE SYNTAX AtmfM4TrapLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single trap log." INDEX { atmfM4TrapLogSrc, atmfM4TrapLogType } ::= { atmfM4TrapLogTable 1 } AtmfM4TrapLogEntry ::= SEQUENCE { atmfM4TrapLogSrc IpAddress, atmfM4TrapLogType INTEGER, atmfM4TrapLogAdminStatus INTEGER, atmfM4TrapLogOperStatus INTEGER, atmfM4TrapLogFullAction INTEGER, atmfM4TrapLogRowStatus RowStatus } atmfM4TrapLogSrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the SNMP agent whose traps are stored in this log." ::= { atmfM4TrapLogEntry 1 } atmfM4TrapLogType OBJECT-TYPE SYNTAX INTEGER { objectCreated(1), objectDeleted(2), configChange(3), stateChange(4), alarm(5) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of traps stored in this log." ::= { atmfM4TrapLogEntry 2 } atmfM4TrapLogAdminStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The management system uses this object to stop and start the operations of this object." DEFVAL { up } ::= { atmfM4TrapLogEntry 3 } atmfM4TrapLogOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), logFull(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the log is capable of performing its normal operations." DEFVAL { up } ::= { atmfM4TrapLogEntry 4 } atmfM4TrapLogFullAction OBJECT-TYPE SYNTAX INTEGER { halt(1), wrap(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the action that should be performed when no more log entries can be created due to a log-full condition. If the value of this object is wrap(2), each new log entry will cause the deletion of the oldest entry still in the log, for as long as the log is still full." DEFVAL { wrap } ::= { atmfM4TrapLogEntry 5 } atmfM4TrapLogRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or to delete an existing row in the table." ::= { atmfM4TrapLogEntry 6 } -- ATM Forum M4 Trap Agent MIB Logged Trap Table atmfM4LoggedTrapTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4LoggedTrapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent logged trap table. This table is used to maintain the traps logged." ::= { atmfM4MIBObjects 41 } atmfM4LoggedTrapEntry OBJECT-TYPE SYNTAX AtmfM4LoggedTrapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single trap in the log. Entries in this table are created automatically but can be deleted by the management system. Entries that represent 'alarm' log types are augmented by the atmfM4LoggedAlarmEntry table." INDEX { atmfM4TrapLogSrc, atmfM4TrapLogType, atmfM4LoggedTrapIndex } ::= { atmfM4LoggedTrapTable 1 } AtmfM4LoggedTrapEntry ::= SEQUENCE { atmfM4LoggedTrapIndex Unsigned32, atmfM4LoggedTrapTime DateAndTime, atmfM4LoggedTrapID Integer32, atmfM4LoggedTrapObject RowPointer, atmfM4LoggedTrapRowStatus RowStatus } atmfM4LoggedTrapIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique number identifying this entry in the log. When the maximum value for this object has been reached, it will wrap around to 0." ::= { atmfM4LoggedTrapEntry 1 } atmfM4LoggedTrapTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time at which this trap was logged." ::= { atmfM4LoggedTrapEntry 2 } atmfM4LoggedTrapID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The type of trap to which this entry applies. Together with the logged trap ID object, this object specifies the entity to which this logged trap referred." ::= { atmfM4LoggedTrapEntry 3 } atmfM4LoggedTrapObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "The object to which this entry applies. By convention, this is the name of the first object in the row in the table referenced. Together with the logged trap ID object, this object specifies the entity to which this logged trap referred. The special value { 0 0 } indicates that the trap refers to the ATM NE entity itself." ::= { atmfM4LoggedTrapEntry 4 } atmfM4LoggedTrapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to delete an existing row in the table. Note that the only value to which a management system can set this object is destroy(6)." ::= { atmfM4LoggedTrapEntry 5 } -- ATM Forum M4 Trap Agent MIB Logged Alarm Table atmfM4LoggedAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfM4LoggedAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent logged alarm trap table. This table is used to maintain extra information for logged traps that represent alarm types." ::= { atmfM4MIBObjects 42 } atmfM4LoggedAlarmEntry OBJECT-TYPE SYNTAX AtmfM4LoggedAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the alarm-specific attributes of a single trap in the log." INDEX { atmfM4TrapLogSrc, atmfM4TrapLogType, atmfM4LoggedTrapIndex } ::= { atmfM4LoggedAlarmTable 1 } AtmfM4LoggedAlarmEntry ::= SEQUENCE { atmfM4LoggedAlarmSeverity AtmfM4AlarmLogSeverity, atmfM4LoggedAlarmBackedUp TruthValue, atmfM4LoggedAlarmBUObject RowPointer, atmfM4LoggedAlarmSpecificProb DisplayString, atmfM4LoggedAlarmRepairAct DisplayString } atmfM4LoggedAlarmSeverity OBJECT-TYPE SYNTAX AtmfM4AlarmLogSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The perceived severity of the alarm, as specified by the agent that generated it." ::= { atmfM4LoggedAlarmEntry 1 } atmfM4LoggedAlarmBackedUp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is true, the agent reported in this trap that the failed object had been backed up. This object is only present if it was included in the alarm trap corresponding to this log entry." ::= { atmfM4LoggedAlarmEntry 2 } atmfM4LoggedAlarmBUObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the object that provided back-up services to the failed object. This object is only present if it was included in the alarm trap corresponding to this log entry." ::= { atmfM4LoggedAlarmEntry 3 } atmfM4LoggedAlarmSpecificProb OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by newline characters. This object is only present if it was included in the alarm trap corresponding to this log entry." ::= { atmfM4LoggedAlarmEntry 4 } atmfM4LoggedAlarmRepairAct OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates proposed repair actions reported by the agent for the the problem identified by the alarm. If more than one action is described in this object, the problem descriptions are separated by newline characters. This object is only present if it was included in the alarm trap corresponding to this log entry." ::= { atmfM4LoggedAlarmEntry 5 } -- ATM M4 MIB Notification types -- Auxiliary definitions for alarms -- Except for perceived severity, the following objects may be -- optionally appended to any alarm notification. atmfM4TrapAlarmSeverity OBJECT-TYPE SYNTAX AtmfM4AlarmLogSeverity MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The perceived severity of the alarm, as specified by the agent that generated it." ::= { atmfM4MIBObjects 43 } atmfM4TrapAlarmBackedUp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "If the value of this object is true, the failed object has been backed up." ::= { atmfM4MIBObjects 44 } atmfM4TrapAlarmBUObject OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Indicates the object that provided back-up services to the failed object." ::= { atmfM4MIBObjects 45 } atmfM4TrapAlarmSpecificProb OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Indicates further refinements to the problem identified by the alarm type. If more than one specific problem is described in this object, the problem descriptions are separated by newline characters." ::= { atmfM4MIBObjects 46 } atmfM4TrapAlarmRepairAct OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Indicates proposed repair actions reported by the agent for the the problem identified by the alarm. If more than one action is described in this object, the problem descriptions are separated by newline characters." ::= { atmfM4MIBObjects 47 } -- Comunications Alarms (interface) atmfM4IfAisAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an AIS alarm condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 1 } atmfM4IfLcdAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an LCD (Loss of Cell Delineation) condition has occurred on the TC Adatpr associated with the specified interface." ::= { atmfM4MIBTraps 2 } atmfM4IfLofAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an LOF (Loss of Frame) condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 3 } atmfM4IfLopAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an LOP (Loss of Pointer) condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 4 } atmfM4IfLosAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an LOS (Loss of Signal) condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 5 } atmfM4IfPayloadMismatchAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a payload type mismatch condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 6 } atmfM4IfXmissionErrAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an transmission error condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 7 } atmfM4IfPathTraceMismatchAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that path trace mismatch condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 8 } atmfM4IfRdiAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an RDI (Remote Defect Indication) condition has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 9 } atmfM4IfSignalLabelMismatchAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a signal label mismatch has occurred on the physical path TP associated with the specified interface." ::= { atmfM4MIBTraps 10 } -- Communications alarms (VPL termination point) atmfM4VplTpAisAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an AIS alarm condition has occurred on the VPL TP associated with the specified interface and VPI." ::= { atmfM4MIBTraps 11 } atmfM4VplTpRdiAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an RDI (Remote Defect Indication) condition has occurred on the VPL TP associated with the specified interface." ::= { atmfM4MIBTraps 12 } -- Communications alarms (VPC termination point) atmfM4VpcTpAisAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an AIS alarm condition has occurred on the VPC TP associated with the specified interface and VPI." ::= { atmfM4MIBTraps 13 } atmfM4VpcTpRdiAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an RDI (Remote Defect Indication) condition has occurred on the VPC TP associated with the specified interface." ::= { atmfM4MIBTraps 14 } -- Communications alarms (VCL termination point) atmfM4VclTpAisAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an AIS alarm condition has occurred on the VCL TP associated with the specified interface and VCI." ::= { atmfM4MIBTraps 15 } atmfM4VclTpRdiAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an RDI (Remote Defect Indication) condition has occurred on the VCL TP associated with the specified interface." ::= { atmfM4MIBTraps 16 } -- Communications alarms (VCC termination point) atmfM4VccTpAisAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an AIS alarm condition has occurred on the VCC TP associated with the specified interface and VCI." ::= { atmfM4MIBTraps 17 } atmfM4VccTpRdiAlarm NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an RDI (Remote Defect Indication) condition has occurred on the VCC TP associated with the specified interface." ::= { atmfM4MIBTraps 18 } -- ATM NE and Hardware Unit Alarms atmfM4HwBackPlaneAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a back-plane failure condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 19 } atmfM4HwCallEstErrAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a call establishment error condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 20 } atmfM4HwCongestionAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a congestion condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 21 } atmfM4HwExtIfDevProbAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an external interface device problem has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 22 } atmfM4HwLineCardAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a line-card problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 23 } atmfM4HwMultiplexerAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a multiplexer problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 24 } atmfM4HwPowerAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a power problem alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 25 } atmfM4HwProcessorAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a processor problem alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 26 } atmfM4HwProtectionPathAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a protection path problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 27 } atmfM4HwReceiverFailAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a receiver failure condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 28 } atmfM4HwPIUnitMissingAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a plug-in unit missing condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 29 } atmfM4HwPIUnitProbAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a plug-in unit problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 30 } atmfM4HwPIUnitMismatchAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a plug-in unit type mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 31 } atmfM4HwTimingProbAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a timing problem alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 32 } atmfM4HwXmitterFailAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a transmitter failure condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 33 } atmfM4HwTrunkCardAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a trunk-card problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 34 } atmfM4HwStorageCapacityAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a storage capacity problem condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 35 } atmfM4HwMemoryMismatchAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a memory mismatch alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 36 } atmfM4HwCorruptDataAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a corrupt data alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 37 } atmfM4HwSwEnvironAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a software environment problem has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 38 } atmfM4HwSwDowloadFailAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a software download failure has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 39 } atmfM4HwVersionMismatchAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a version mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 40 } atmfM4HwFanFailAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a cooling fan failure condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 41 } atmfM4HwDoorOpenAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that an enclosure door open condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 42 } atmfM4HwFuseFailAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a fuse failure alarm condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 43 } atmfM4HwHighTempAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a high temperature condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 44 } -- Software alarms atmfM4SwVersionMismatchAlarm NOTIFICATION-TYPE OBJECTS { entPhysicalIndex, atmfM4HwInstalledSwIndex, atmfM4TrapAlarmSeverity } STATUS current DESCRIPTION "Indicates that a version mismatch condition has occurred on the hardware unit associated with the specified index. A hardware index of 0 indicates that the error occurred in the ATM NE but not in any one hardware unit maintained in the MIB table." ::= { atmfM4MIBTraps 45 } -- State change notification traps: atmfM4VplTpUp NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi } STATUS current DESCRIPTION "Indicates that the operational state of the specified VPL termination point has transitioned to 'up'." ::= { atmfM4MIBTraps 46 } atmfM4VplTpDown NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi } STATUS current DESCRIPTION "Indicates that the operational state of the specified VPL termination point has transitioned to 'down'." ::= { atmfM4MIBTraps 47 } atmfM4VclTpUp NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci } STATUS current DESCRIPTION "Indicates that the operational state of the specified VCL termination point has transitioned to 'up'." ::= { atmfM4MIBTraps 48 } atmfM4VclTpDown NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci } STATUS current DESCRIPTION "Indicates that the operational state of the specified VCL termination point has transitioned to 'down'." ::= { atmfM4MIBTraps 49 } atmfM4VplXConnUp NOTIFICATION-TYPE OBJECTS { atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi } STATUS current DESCRIPTION "Indicates that the operational state of the specified VPL cross-connection has transitioned to 'up'." ::= { atmfM4MIBTraps 50 } atmfM4VplXConnDown NOTIFICATION-TYPE OBJECTS { atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi } STATUS current DESCRIPTION "Indicates that the operational state of the specified VPL cross-connection has transitioned to 'down'." ::= { atmfM4MIBTraps 51 } atmfM4VclXConnUp NOTIFICATION-TYPE OBJECTS { atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci } STATUS current DESCRIPTION "Indicates that the operational state of the specified VCL cross-connection has transitioned to 'up'." ::= { atmfM4MIBTraps 52 } atmfM4VclXConnDown NOTIFICATION-TYPE OBJECTS { atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci } STATUS current DESCRIPTION "Indicates that the operational state of the specified VCL cross-connection has transitioned to 'down'." ::= { atmfM4MIBTraps 53 } atmfM4HwUnitUp NOTIFICATION-TYPE OBJECTS { entPhysicalClass } STATUS current DESCRIPTION "Indicates that the operational state of the specified hardware unit has transitioned to 'up'." ::= { atmfM4MIBTraps 54 } atmfM4HwUnitDown NOTIFICATION-TYPE OBJECTS { entPhysicalClass } STATUS current DESCRIPTION "Indicates that the operational state of the specified hardware unit has transitioned to 'down'." ::= { atmfM4MIBTraps 55 } -- Object creation and deletion notification traps: atmfM4AtmCellIfCreated NOTIFICATION-TYPE OBJECTS { ifIndex, atmfM4IfType } STATUS current DESCRIPTION "Indicates that an ATM cell layer interface has just been created on the interface." ::= { atmfM4MIBTraps 56 } atmfM4AtmCellIfDeleted NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "Indicates that the ATM cell layer interface has just been deleted." ::= { atmfM4MIBTraps 57 } atmfM4VpcTpCreated NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi } STATUS current DESCRIPTION "Indicates that the VPC termination point has just been created." ::= { atmfM4MIBTraps 58 } atmfM4VpcTpDeleted NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi } STATUS current DESCRIPTION "Indicates that the VPC termination point has just been deleted." ::= { atmfM4MIBTraps 59 } atmfM4VccTpCreated NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci } STATUS current DESCRIPTION "Indicates that the VCC termination point has just been created." ::= { atmfM4MIBTraps 60 } atmfM4VccTpDeleted NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci } STATUS current DESCRIPTION "Indicates that the VCC termination point has just been deleted." ::= { atmfM4MIBTraps 61 } atmfM4VplXConnCreated NOTIFICATION-TYPE OBJECTS { atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi } STATUS current DESCRIPTION "Indicates that the VPL cross-connection has just been created. When a cross-connection is created along with its VPL endpoints, this trap should be emitted to indicate the creation of the entire group of objects." ::= { atmfM4MIBTraps 62 } atmfM4VplXConnDeleted NOTIFICATION-TYPE OBJECTS { atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi } STATUS current DESCRIPTION "Indicates that the VPL cross-connection has just been deleted. When a cross-connection is deleted along with its VPL endpoints, this trap should be emitted to indicate the deletion of the entire group of objects." ::= { atmfM4MIBTraps 63 } atmfM4VclXConnCreated NOTIFICATION-TYPE OBJECTS { atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci } STATUS current DESCRIPTION "Indicates that the VCL cross-connection has just been created. When a cross-connection is created along with its VCL endpoints, this trap should be emitted to indicate the creation of the entire group of objects." ::= { atmfM4MIBTraps 64 } atmfM4VclXConnDeleted NOTIFICATION-TYPE OBJECTS { atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci } STATUS current DESCRIPTION "Indicates that the VCL cross-connection has just been deleted. When a cross-connection is deleted along with its VCL endpoints, this trap should be emitted to indicate the deletion of the entire group of objects." ::= { atmfM4MIBTraps 65 } atmfM4HwUnitCreated NOTIFICATION-TYPE OBJECTS { entPhysicalContainedIn, entPhysicalParentRelPos, entPhysicalClass} STATUS current DESCRIPTION "Indicates that the specified hardware unit has been installed at the specified location." ::= { atmfM4MIBTraps 66 } atmfM4HwUnitDeleted NOTIFICATION-TYPE OBJECTS { entPhysicalContainedIn, entPhysicalParentRelPos, entPhysicalClass} STATUS current DESCRIPTION "Indicates that the specified hardware unit has been removed or de-instaleld from the specified location." ::= { atmfM4MIBTraps 67 } atmfM4InstalledSwCreated NOTIFICATION-TYPE OBJECTS { atmfM4HwInstalledSwHwIndex, hrSWInstalledIndex, hrSWInstalledName } STATUS current DESCRIPTION "Indicates that the specified software package has been installed." ::= { atmfM4MIBTraps 68 } atmfM4InstalledSwDeleted NOTIFICATION-TYPE OBJECTS { atmfM4HwInstalledSwHwIndex, hrSWInstalledIndex, hrSWInstalledName } STATUS current DESCRIPTION "Indicates that the specified software package has been removed." ::= { atmfM4MIBTraps 69 } -- Configuration change notification traps. atmfM4IfChanged NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "Indicates that the configuration of the interface has been changed." ::= { atmfM4MIBTraps 70 } atmfM4VplTpChanged NOTIFICATION-TYPE OBJECTS { ifIndex, atmVplVpi } STATUS current DESCRIPTION "Indicates that the VPL termination point config. has been changed." ::= { atmfM4MIBTraps 71 } atmfM4VclTpChanged NOTIFICATION-TYPE OBJECTS { ifIndex, atmVclVpi, atmVclVci } STATUS current DESCRIPTION "Indicates that the VCL termination point config. has been changed." ::= { atmfM4MIBTraps 72 } atmfM4VplXConnChanged NOTIFICATION-TYPE OBJECTS { atmVpCrossConnectIndex, atmVpCrossConnectLowIfIndex, atmVpCrossConnectLowVpi, atmVpCrossConnectHighIfIndex, atmVpCrossConnectHighVpi } STATUS current DESCRIPTION "Indicates that the VPL cross-connection config. has been changed." ::= { atmfM4MIBTraps 73 } atmfM4VclXConnChanged NOTIFICATION-TYPE OBJECTS { atmVcCrossConnectIndex, atmVcCrossConnectLowIfIndex, atmVcCrossConnectLowVpi, atmVcCrossConnectLowVci, atmVcCrossConnectHighIfIndex, atmVcCrossConnectHighVpi, atmVcCrossConnectHighVci } STATUS current DESCRIPTION "Indicates that the VCL cross-connection config. has been changed." ::= { atmfM4MIBTraps 74 } atmfM4HwUnitChanged NOTIFICATION-TYPE OBJECTS { entPhysicalIndex } STATUS current DESCRIPTION "Indicates that the specified hardware unit config. has changed." ::= { atmfM4MIBTraps 75 } atmfM4InstalledSwChanged NOTIFICATION-TYPE OBJECTS { hrSWInstalledIndex } STATUS current DESCRIPTION "Indicates that the specified software package config. has changed." ::= { atmfM4MIBTraps 76 } -- Conformance statements atmfM4Groups OBJECT IDENTIFIER ::= { atmfM4MIBCompliance 1 } atmfM4Compliances OBJECT IDENTIFIER ::= { atmfM4MIBCompliance 2 } -- compliance statements atmfM4Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statements are listed as a set up conformance units that correspond to each table. Support for all tables is mandatory." MODULE -- this module MANDATORY-GROUPS {atmfM4General, atmfM4PhysPathTpGroup, atmfM4TcAdaptorGroup, atmfM4AtmLayerGroup, atmfM4VplGroup, atmfM4VclGroup, atmfM4VpXConnGroup, atmfM4VcXConnGroup, atmfM4VpNextVpiGroup, atmfM4VcNextVciGroup, atmfM4CellProtoCurrGroup, atmfM4CellProtoHistGroup, atmfM4CellProtoErrorGroup, atmfM4TcProtoCurrGroup, atmfM4TcProtoHistGroup, atmfM4VpUpcNpcCurrGroup, atmfM4VpUpcNpcHistGroup, atmfM4VcUpcNpcCurrGroup, atmfM4VcUpcNpcHistGroup, atmfM4VpTestGroup, atmfM4VcTestGroup, atmfM4EquipGroup, atmfM4EquipHolderGroup, atmfM4PlugInUnitGroup, atmfM4HwRunningSwGroup, atmfM4HwInstalledSwGroup, atmfM4AlarmSevGroup, atmfM4TrapForwardingGroup, atmfM4TrapLogGroup, atmfM4LoggedTrapGroup, atmfM4LoggedAlarmGroup, atmfM4NotificationsGroup} ::= { atmfM4Compliances 1 } -- units of conformance atmfM4General OBJECT-GROUP OBJECTS {atmfM4NeVendor, atmfM4NeVersion, atmfM4NeStartTime, atmfM4NeAlarmSeverityIndex, atmfM4NeSuppressZeroStats} STATUS current DESCRIPTION "NE high level objects" ::= { atmfM4Groups 1} atmfM4PhysPathTpGroup OBJECT-GROUP OBJECTS {atmfM4PhysPathTpHwUnitIndex, atmfM4PhysPathTpPortID, atmfM4PhysPathTpAlarmSeverityIndex} STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the physical path termination point" ::= { atmfM4Groups 2 } atmfM4TcAdaptorGroup OBJECT-GROUP OBJECTS {atmfM4TcACellScrambling, atmfM4TcAlarmSeverityIndex} STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the TC Adaptor." ::= { atmfM4Groups 3 } atmfM4AtmLayerGroup OBJECT-GROUP OBJECTS {atmfM4IfType, atmfM4IfLoopbackLocationCode, atmfM4IfSubscriberAddress, atmfM4IfPreferredCarrier, atmfM4IfFarEndCarrierNetwork} STATUS current DESCRIPTION "The ATM Forum M4 interface Configuration table extensions for the ATM cell layer." ::= { atmfM4Groups 4 } atmfM4VplGroup OBJECT-GROUP OBJECTS {atmfM4VplSegEndPt} STATUS current DESCRIPTION "The ATM Forum M4 VPL Termination Point Configuration table extensions. " ::= { atmfM4Groups 5 } atmfM4VclGroup OBJECT-GROUP OBJECTS {atmfM4VclSegEndPt} STATUS current DESCRIPTION "The ATM Forum M4 VCL Termination Point Configuration table extensions." ::= { atmfM4Groups 6 } atmfM4VpXConnGroup OBJECT-GROUP OBJECTS {atmfM4VpXConnRecover} STATUS current DESCRIPTION "The ATM Forum M4 VP Cross-Connect Configuration table extensions." ::= { atmfM4Groups 7 } atmfM4VcXConnGroup OBJECT-GROUP OBJECTS {atmfM4VcXConnRecover} STATUS current DESCRIPTION "The ATM Forum M4 VC Cross-Connect Configuration table extensions." ::= { atmfM4Groups 8 } atmfM4VpNextVpiGroup OBJECT-GROUP OBJECTS {atmfM4VpNextVpiValue} STATUS current DESCRIPTION "The ATM Forum M4 VP Next-VPI value table." ::= { atmfM4Groups 9 } atmfM4VcNextVciGroup OBJECT-GROUP OBJECTS {atmfM4VcNextVciValue} STATUS current DESCRIPTION "The ATM Forum M4 VC Next-VCI value table." ::= { atmfM4Groups 10 } atmfM4CellProtoCurrGroup OBJECT-GROUP OBJECTS {atmfM4CellProtoCurrSuspect, atmfM4CellProtoCurrElapsedTime, atmfM4CellProtoCurrSupprIntvls, atmfM4CellProtoCurrProtoErrors, atmfM4CellProtoCurrInOAMCells} STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring Current Data table." ::= { atmfM4Groups 11 } atmfM4CellProtoHistGroup OBJECT-GROUP OBJECTS {atmfM4CellProtoHistSuspect, atmfM4CellProtoHistElapsedTime, atmfM4CellProtoHistSupprIntvls, atmfM4CellProtoHistProtoErrors, atmfM4CellProtoHistInOAMCells} STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring History Data table." ::= { atmfM4Groups 12 } atmfM4CellProtoErrorGroup OBJECT-GROUP OBJECTS {atmfM4CellProtoErrorTime, atmfM4CellProtoErrorReason, atmfM4CellProtoErrorVpi, atmfM4CellProtoErrorVci} STATUS current DESCRIPTION "The ATM Forum M4 Cell Protocol Monitoring Error Log table." ::= { atmfM4Groups 13 } atmfM4TcProtoCurrGroup OBJECT-GROUP OBJECTS {atmfM4TcProtoCurrSuspect, atmfM4TcProtoCurrElapsedTime, atmfM4TcProtoCurrSupprIntvls, atmfM4TcProtoCurrDiscardHECViol} STATUS current DESCRIPTION "The ATM Forum M4 TC Adaptor Protocol Monitoring Current Data table." ::= { atmfM4Groups 14 } atmfM4TcProtoHistGroup OBJECT-GROUP OBJECTS {atmfM4TcProtoHistSuspect, atmfM4TcProtoHistElapsedTime, atmfM4TcProtoHistSupprIntvls, atmfM4TcProtoHistDiscardHECViol} STATUS current DESCRIPTION "The ATM Forum M4 TC Adaptor Protocol Monitoring History Data table." ::= { atmfM4Groups 15 } atmfM4VpUpcNpcCurrGroup OBJECT-GROUP OBJECTS {atmfM4VpUpcNpcCurrSuspect, atmfM4VpUpcNpcCurrElapsedTime, atmfM4VpUpcNpcCurrSupprIntvls, atmfM4VpUpcNpcCurrDiscardedCells, atmfM4VpUpcNpcCurrDiscardedClp0, atmfM4VpUpcNpcCurrPassedCells, atmfM4VpUpcNpcCurrPassedClp0} STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VPL termination points." ::= { atmfM4Groups 16 } atmfM4VpUpcNpcHistGroup OBJECT-GROUP OBJECTS {atmfM4VpUpcNpcHistSuspect, atmfM4VpUpcNpcHistElapsedTime, atmfM4VpUpcNpcHistSupprIntvls, atmfM4VpUpcNpcHistDiscardedCells, atmfM4VpUpcNpcHistDiscardedClp0, atmfM4VpUpcNpcHistPassedCells, atmfM4VpUpcNpcHistPassedClp0} STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VPL termination points." ::= { atmfM4Groups 17 } atmfM4VcUpcNpcCurrGroup OBJECT-GROUP OBJECTS {atmfM4VcUpcNpcCurrSuspect, atmfM4VcUpcNpcCurrElapsedTime, atmfM4VcUpcNpcCurrSupprIntvls, atmfM4VcUpcNpcCurrDiscardedCells, atmfM4VcUpcNpcCurrDiscardedClp0, atmfM4VcUpcNpcCurrPassedCells, atmfM4VcUpcNpcCurrPassedClp0} STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring Current Data table for VCL termination points" ::= { atmfM4Groups 18 } atmfM4VcUpcNpcHistGroup OBJECT-GROUP OBJECTS {atmfM4VcUpcNpcHistSuspect, atmfM4VcUpcNpcHistElapsedTime, atmfM4VcUpcNpcHistSupprIntvls, atmfM4VcUpcNpcHistDiscardedCells, atmfM4VcUpcNpcHistDiscardedClp0, atmfM4VcUpcNpcHistPassedCells, atmfM4VcUpcNpcHistPassedClp0} STATUS current DESCRIPTION "The ATM Forum M4 UPC/NPC Disagreement Monitoring History Data table for VCL termination points." ::= { atmfM4Groups 19 } atmfM4VpTestGroup OBJECT-GROUP OBJECTS {atmfM4VpTestId, atmfM4VpTestStatus, atmfM4VpTestType, atmfM4VpTestResult, atmfM4VpTestCode, atmfM4VpTestOwner} STATUS current DESCRIPTION "The ATM Forum M4 VP Termination Point Test table." ::= { atmfM4Groups 20 } atmfM4VcTestGroup OBJECT-GROUP OBJECTS {atmfM4VcTestId, atmfM4VcTestStatus, atmfM4VcTestType, atmfM4VcTestResult, atmfM4VcTestCode, atmfM4VcTestOwner} STATUS current DESCRIPTION "The ATM Forum M4 VC Termination Point Test table." ::= { atmfM4Groups 21 } atmfM4EquipGroup OBJECT-GROUP OBJECTS {atmfM4EquipAdminStatus, atmfM4EquipLocation, atmfM4EquipOperStatus, atmfM4EquipVendor, atmfM4EquipVersion, atmfM4EquipUserLabel, atmfM4EquipAlarmSeverityIndex} STATUS current DESCRIPTION "The ATM Forum M4 Equipment table." ::= { atmfM4Groups 22 } atmfM4EquipHolderGroup OBJECT-GROUP OBJECTS {atmfM4EquipHolderType, atmfM4EquipHolderAcceptableTypes, atmfM4EquipHolderSlotStatus, atmfM4EquipHolderSwLoad} STATUS current DESCRIPTION "The ATM Forum M4 Equipment Holder table." ::= { atmfM4Groups 23 } atmfM4PlugInUnitGroup OBJECT-GROUP OBJECTS {atmfM4PlugInUnitAdminStatus, atmfM4PlugInUnitAvailStatus, atmfM4PlugInUnitOperStatus, atmfM4PlugInUnitVendor, atmfM4PlugInUnitVersion, atmfM4PlugInUnitAlarmSeverityIndex} STATUS current DESCRIPTION "The ATM Forum M4 Plug-In Unit table." ::= { atmfM4Groups 24 } atmfM4HwRunningSwGroup OBJECT-GROUP OBJECTS {atmfM4HwRunningSwSwIndex} STATUS current DESCRIPTION "The ATM Forum M4 Hardware Unit/Running Software table." ::= { atmfM4Groups 25 } atmfM4HwInstalledSwGroup OBJECT-GROUP OBJECTS {atmfM4HwInstalledSwSwIndex, atmfM4HwSwAlarmSeverityIndex} STATUS current DESCRIPTION "The ATM Forum M4 Hardware Unit/Installed Software table" ::= { atmfM4Groups 26 } atmfM4AlarmSevGroup OBJECT-GROUP OBJECTS {atmfM4AlarmSevProfileRowStatus, atmfM4AlarmSeverity, atmfM4AlarmSevDefault, atmfM4AlarmSevProfileIndexNext } STATUS current DESCRIPTION "Alarm handling objects" ::= { atmfM4Groups 27 } atmfM4TrapForwardingGroup OBJECT-GROUP OBJECTS {atmfM4TrapForwardingDest, atmfM4ForwardedTrapId, atmfM4ForwardedTrapObject, atmfM4TrapForwardingPort, atmfM4LowestForwardedSeverity, atmfM4ForwardedIndeterminate, atmfM4TrapForwardingRowStatus} STATUS current DESCRIPTION "Trap forwarding table" ::= { atmfM4Groups 28 } atmfM4TrapLogGroup OBJECT-GROUP OBJECTS {atmfM4TrapLogAdminStatus, atmfM4TrapLogOperStatus, atmfM4TrapLogFullAction, atmfM4TrapLogRowStatus} STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent log table." ::= { atmfM4Groups 29 } atmfM4LoggedTrapGroup OBJECT-GROUP OBJECTS {atmfM4LoggedTrapTime, atmfM4LoggedTrapID, atmfM4LoggedTrapObject, atmfM4LoggedTrapRowStatus} STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent logged trap table." ::= { atmfM4Groups 30 } atmfM4LoggedAlarmGroup OBJECT-GROUP OBJECTS {atmfM4LoggedAlarmSeverity, atmfM4LoggedAlarmBackedUp, atmfM4LoggedAlarmBUObject, atmfM4LoggedAlarmSpecificProb, atmfM4LoggedAlarmRepairAct, atmfM4TrapAlarmSeverity, atmfM4TrapAlarmBackedUp, atmfM4TrapAlarmBUObject, atmfM4TrapAlarmSpecificProb, atmfM4TrapAlarmRepairAct} STATUS current DESCRIPTION "The ATM Forum M4 Trap Agent logged alarm trap table." ::= { atmfM4Groups 31 } atmfM4NotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS {atmfM4IfAisAlarm, atmfM4IfLcdAlarm, atmfM4IfLofAlarm, atmfM4IfLopAlarm, atmfM4IfLosAlarm, atmfM4IfPayloadMismatchAlarm, atmfM4IfXmissionErrAlarm, atmfM4IfPathTraceMismatchAlarm, atmfM4IfRdiAlarm, atmfM4IfSignalLabelMismatchAlarm, atmfM4VplTpAisAlarm, atmfM4VplTpRdiAlarm, atmfM4VpcTpAisAlarm, atmfM4VpcTpRdiAlarm, atmfM4VclTpAisAlarm, atmfM4VclTpRdiAlarm, atmfM4VccTpAisAlarm, atmfM4VccTpRdiAlarm, atmfM4HwBackPlaneAlarm, atmfM4HwCallEstErrAlarm, atmfM4HwCongestionAlarm, atmfM4HwExtIfDevProbAlarm, atmfM4HwLineCardAlarm, atmfM4HwMultiplexerAlarm, atmfM4HwPowerAlarm, atmfM4HwProcessorAlarm, atmfM4HwProtectionPathAlarm, atmfM4HwReceiverFailAlarm, atmfM4HwPIUnitMissingAlarm, atmfM4HwPIUnitProbAlarm, atmfM4HwPIUnitMismatchAlarm, atmfM4HwTimingProbAlarm, atmfM4HwXmitterFailAlarm, atmfM4HwTrunkCardAlarm, atmfM4HwStorageCapacityAlarm, atmfM4HwMemoryMismatchAlarm, atmfM4HwCorruptDataAlarm, atmfM4HwSwEnvironAlarm, atmfM4HwSwDowloadFailAlarm, atmfM4HwVersionMismatchAlarm, atmfM4HwFanFailAlarm, atmfM4HwDoorOpenAlarm, atmfM4HwFuseFailAlarm, atmfM4HwHighTempAlarm, atmfM4SwVersionMismatchAlarm, atmfM4VplTpUp, atmfM4VplTpDown, atmfM4VclTpUp, atmfM4VclTpDown, atmfM4VplXConnUp, atmfM4VplXConnDown, atmfM4VclXConnUp, atmfM4VclXConnDown, atmfM4HwUnitUp, atmfM4HwUnitDown, atmfM4AtmCellIfCreated, atmfM4AtmCellIfDeleted, atmfM4VpcTpCreated, atmfM4VpcTpDeleted, atmfM4VccTpCreated, atmfM4VccTpDeleted, atmfM4VplXConnCreated, atmfM4VplXConnDeleted, atmfM4VclXConnCreated, atmfM4VclXConnDeleted, atmfM4HwUnitCreated, atmfM4HwUnitDeleted, atmfM4InstalledSwCreated, atmfM4InstalledSwDeleted, atmfM4IfChanged, atmfM4VplTpChanged, atmfM4VclTpChanged, atmfM4VplXConnChanged, atmfM4VclXConnChanged, atmfM4HwUnitChanged, atmfM4InstalledSwChanged } STATUS current DESCRIPTION "The ATM Forum M4 notification list." ::= { atmfM4Groups 32 } END