ADSL-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, NOTIFICATION-TYPE, Integer32, enterprises FROM SNMPv2-SMI DisplayString, RowStatus, TruthValue FROM SNMPv2-TC ifIndex FROM RFC1213-MIB ; AdslLineProfileType ::= INTEGER adslMIB MODULE-IDENTITY LAST-UPDATED "9801121700Z" ORGANIZATION "ADSL Forum" CONTACT-INFO " John Burgess Predictive Systems, Inc. 25A Vreeland Rd. Florham Park, NJ 07932 USA Tel: +1 201-301-5610 Fax: +1 201-301-5699 E-mail: jtburgess@predictive.com Greg Bathrick AG Communication Systems 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-mail: bathricg@agcs.com " DESCRIPTION "The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such Line is indexed by ifIndex and appears as an interface on a central DSLAM (Digital Subscriber Line Access Mux.) Attributes on the ATUR are proxied by the DSLAM. ADSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus an ADSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to adsl(94), fast(125), and interleaved(124), respectively. The ifStackTable is used to link the entries together. Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs-- interval of Seconds in which xxx occurs (e.g., xxx=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks-- Blocks, a data unit, see adslAtuXChanCrcBlockLength " ::= { enterprises 99999 } -- temporary assignment clause used for compilation -- reasons only. Upon assignment by the IETF, this -- value will be changed. During this interim -- period, it is recommended that implementors of -- this MIB assign this to a point under their -- private enterprise assignment tree. adslLineMib OBJECT IDENTIFIER ::= { adslMIB 1 } adslMibObjects OBJECT IDENTIFIER ::= { adslLineMib 1 } adslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 1 } adslLineEntry OBJECT-TYPE SYNTAX AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineTable." INDEX { ifIndex } ::= { adslLineTable 1 } AdslLineEntry ::= SEQUENCE { adslLineCoding INTEGER, adslLineType INTEGER, adslLineSpecific OBJECT IDENTIFIER, adslLineConfProfile AdslLineProfileType, adslLineAlarmConfProfile AdslLineProfileType } adslLineCoding OBJECT-TYPE SYNTAX INTEGER { other (1), dmt (2), -- Discrete MultiTone cap (3), -- Carrierless Amplitude & Phase modulation qam (4) -- Quadrature Amplitude Modulation } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the ADSL coding type used on this line. Other types may be added in the future." ::= { adslLineEntry 1 } adslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- fast channel exists only interleavedOnly (3), -- interleaved channel exists -- only fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both fast or interleaved -- channnels exist } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, a value other than noChannel(1), this object defines which channel type(s) are suppored. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." ::= { adslLineEntry 2 } adslLineSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM." ::= { adslLineEntry 3 } adslLineConfProfile OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. In the case which the configuration profile has not been set, the value will be set to '0'. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslLineEntry 4 } adslLineAlarmConfProfile OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. In the case which the configuration profile has not been set, the value will be set to '0'. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslLineEntry 5 } adslAtucPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 2 } adslAtucPhysEntry OBJECT-TYPE SYNTAX AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucPhysTable." INDEX { ifIndex } ::= { adslAtucPhysTable 1 } AdslAtucPhysEntry ::= SEQUENCE { adslAtucInvSerialNumber DisplayString, adslAtucInvVendorID Integer32, adslAtucInvVersionNumber Integer32, adslAtucCurrSnrMgn INTEGER, adslAtucCurrAtn INTEGER, adslAtucCurrStatus INTEGER, adslAtucCurrOutputPwr INTEGER, adslAtucCurrAttainableRate Integer32 } -- inventory group -- -- These items should describe the lowest level identifiable -- component, be it a stand-alone modem, a card in a rack, -- a child-board, etc. -- adslAtucInvSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific string that identifies the vendor equipment." ::= { adslAtucPhysEntry 1 } adslAtucInvVendorID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID assigned by T1E1.413 according to its Annex D." ::= { adslAtucPhysEntry 2 } adslAtucInvVersionNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific Version number sent by this ATU as part of the initialization messages." ::= { adslAtucPhysEntry 3 } -- current status group -- adslAtucCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." ::= { adslAtucPhysEntry 4 } adslAtucCurrAtn OBJECT-TYPE SYNTAX INTEGER(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. This is measured in in tenth dB." ::= { adslAtucPhysEntry 5 } adslAtucCurrStatus OBJECT-TYPE SYNTAX INTEGER(1..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "Status indicates current state ATUC line. This is a bit-map of possible conditions. The various bit positions are: 1 noDefect There no defects on the line 2 lossOfFraming ATUC failure due to not receiving valid frame. 4 lossOfSignal ATUC failure due to not receiving signal. 8 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 16 lossOfLink ATUC failure due to inability to link with ATUR. 32 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 64 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 128 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 256 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 512 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 } adslAtucCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU." ::= { adslAtucPhysEntry 7 } adslAtucCurrAttainableRate OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAtucPhysEntry 8 } adslAturPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 3 } adslAturPhysEntry OBJECT-TYPE SYNTAX AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturPhysTable." INDEX { ifIndex } ::= { adslAturPhysTable 1 } AdslAturPhysEntry ::= SEQUENCE { adslAturInvSerialNumber DisplayString, adslAturInvVendorID Integer32, adslAturInvVersionNumber Integer32, adslAturCurrSnrMgn INTEGER, adslAturCurrAtn INTEGER, adslAturCurrStatus INTEGER, adslAturCurrOutputPwr INTEGER, adslAturCurrAttainableRate Integer32 } -- inventory group -- adslAturInvSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific string that identifies the vendor equipment." ::= { adslAturPhysEntry 1 } adslAturInvVendorID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID assigned by T1E1.413 according to its Annex D." ::= { adslAturPhysEntry 2 } adslAturInvVersionNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific Version number sent by this ATU as part of the initialization messages." ::= { adslAturPhysEntry 3 } -- current status group -- adslAturCurrSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal." ::= { adslAturPhysEntry 4 } adslAturCurrAtn OBJECT-TYPE SYNTAX INTEGER(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU." ::= { adslAturPhysEntry 5 } adslAturCurrStatus OBJECT-TYPE SYNTAX INTEGER(1..7) MAX-ACCESS read-only STATUS current DESCRIPTION "Status indicates current state ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 1 noDefect There no defects on the line 2 lossOfFraming ATUR failure due to not receiving valid frame 4 lossOfSignal ATUR failure due to not receiving signal 8 lossOfPower ATUR failure due to loss of power 32 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus." ::= { adslAturPhysEntry 6 } adslAturCurrOutputPwr OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU." ::= { adslAturPhysEntry 7 } adslAturCurrAttainableRate OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAturPhysEntry 8 } adslAtucChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 4 } adslAtucChanEntry OBJECT-TYPE SYNTAX AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucChanTable." INDEX { ifIndex } ::= { adslAtucChanTable 1 } AdslAtucChanEntry ::= SEQUENCE { adslAtucChanInterleaveDelay Gauge32, adslAtucChanCurrTxRate Gauge32, adslAtucChanPrevTxRate Gauge32, adslAtucChanCrcBlockLength Gauge32 } -- current group -- adslAtucChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel per ANSI T1.413, == (S-factor x d) ------------- 4 milli-seconds, where 'd' is the Interleaving Depth. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchName." ::= { adslAtucChanEntry 1 } adslAtucChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAtucChanEntry 2 } adslAtucChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAtucChanEntry 3 } adslAtucChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "byte" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates." ::= { adslAtucChanEntry 4 } adslAturChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 5 } adslAturChanEntry OBJECT-TYPE SYNTAX AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturChanTable." INDEX { ifIndex } ::= { adslAturChanTable 1 } AdslAturChanEntry ::= SEQUENCE { adslAturChanInterleaveDelay Gauge32, adslAturChanCurrTxRate Gauge32, adslAturChanPrevTxRate Gauge32, adslAturChanCrcBlockLength Gauge32 } -- current group -- adslAturChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel per ANSI T1.413, == (S-factor x d) ------------- 4 milli-seconds, where 'd' is the Interleaving Depth. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchName." ::= { adslAturChanEntry 1 } adslAturChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAturChanEntry 2 } adslAturChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAturChanEntry 3 } adslAturChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates." ::= { adslAturChanEntry 4 } adslAtucPhysPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 6 } adslAtucPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucPhysPerfDataTable." INDEX { ifIndex } ::= { adslAtucPhysPerfDataTable 1 } AdslAtucPerfDataEntry ::= SEQUENCE { adslAtucPerfLof Counter32, adslAtucPerfLos Counter32, adslAtucPerfLol Counter32, adslAtucPerfLpr Counter32, adslAtucPerfES Counter32, adslAtucPerfValidIntervals INTEGER, adslAtucPerfInvalidIntervals INTEGER, adslAtucPerfCurr15MinTimeElapsed INTEGER, adslAtucPerfCurr15MinLofs Gauge32, adslAtucPerfCurr15MinLoss Gauge32, adslAtucPerfCurr15MinLols Gauge32, adslAtucPerfCurr15MinLprs Gauge32, adslAtucPerfCurr15MinESs Gauge32, adslAtucPerfCurr1DayTimeElapsed INTEGER, adslAtucPerfCurr1DayLofs Gauge32, adslAtucPerfCurr1DayLoss Gauge32, adslAtucPerfCurr1DayLols Gauge32, adslAtucPerfCurr1DayLprs Gauge32, adslAtucPerfCurr1DayESs Gauge32, adslAtucPerfPrev1DayMoniSecs INTEGER, adslAtucPerfPrev1DayLofs Gauge32, adslAtucPerfPrev1DayLoss Gauge32, adslAtucPerfPrev1DayLols Gauge32, adslAtucPerfPrev1DayLprs Gauge32, adslAtucPerfPrev1DayESs Gauge32 } -- Event Counters -- -- Also see adslAtucIntervalTable for 15 minute interval -- elapsed counters. -- adslAtucPerfLof OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAtucPerfDataEntry 1 } adslAtucPerfLos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAtucPerfDataEntry 2 } adslAtucPerfLol OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Link failures since agent reset." ::= { adslAtucPerfDataEntry 3 } adslAtucPerfLpr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAtucPerfDataEntry 4 } adslAtucPerfES OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 5 } -- general 15 min interval information -- adslAtucPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAtucInterval Table for which valid data has been stored. This value will be equal to the maximum number of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAtucPerfDataEntry 6 } adslAtucPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals which no valid data is available." ::= { adslAtucPerfDataEntry 7 } -- 15 min current performance group -- adslAtucPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAtucPerfDataEntry 8 } adslAtucPerfCurr15MinLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAtucPerfDataEntry 9 } adslAtucPerfCurr15MinLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAtucPerfDataEntry 10 } adslAtucPerfCurr15MinLols OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Link." ::= { adslAtucPerfDataEntry 11 } adslAtucPerfCurr15MinLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAtucPerfDataEntry 12 } adslAtucPerfCurr15MinESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 13 } -- 1 Day current and previous performance group -- adslAtucPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1Day interval." ::= { adslAtucPerfDataEntry 14 } adslAtucPerfCurr1DayLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 15 } adslAtucPerfCurr1DayLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 16 } adslAtucPerfCurr1DayLols OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 17 } adslAtucPerfCurr1DayLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 18 } adslAtucPerfCurr1DayESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 19 } adslAtucPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring dara can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAtucPerfDataEntry 20 } adslAtucPerfPrev1DayLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1 day period." ::= { adslAtucPerfDataEntry 21 } adslAtucPerfPrev1DayLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1 day period." ::= { adslAtucPerfDataEntry 22 } adslAtucPerfPrev1DayLols OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link within the most recent previous 1 day period." ::= { adslAtucPerfDataEntry 23 } adslAtucPerfPrev1DayLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1 day period." ::= { adslAtucPerfDataEntry 24 } adslAtucPerfPrev1DayESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1 day period. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 25 } adslAturPhysPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 7 } adslAturPerfDataEntry OBJECT-TYPE SYNTAX AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturPhysPerfDataTable." INDEX { ifIndex } ::= { adslAturPhysPerfDataTable 1 } AdslAturPerfDataEntry ::= SEQUENCE { adslAturPerfLof Counter32, adslAturPerfLos Counter32, adslAturPerfLpr Counter32, adslAturPerfES Counter32, adslAturPerfValidIntervals INTEGER, adslAturPerfInvalidIntervals INTEGER, adslAturPerfCurr15MinTimeElapsed INTEGER, adslAturPerfCurr15MinLofs Gauge32, adslAturPerfCurr15MinLoss Gauge32, adslAturPerfCurr15MinLprs Gauge32, adslAturPerfCurr15MinESs Gauge32, adslAturPerfCurr1DayTimeElapsed INTEGER, adslAturPerfCurr1DayLofs Gauge32, adslAturPerfCurr1DayLoss Gauge32, adslAturPerfCurr1DayLprs Gauge32, adslAturPerfCurr1DayESs Gauge32, adslAturPerfPrev1DayMoniSecs INTEGER, adslAturPerfPrev1DayLofs Gauge32, adslAturPerfPrev1DayLoss Gauge32, adslAturPerfPrev1DayLprs Gauge32, adslAturPerfPrev1DayESs Gauge32 } -- Event (Raw) Counters -- -- Also see adslAturIntervalTable for 15 minute interval -- elapsed counters. -- adslAturPerfLof OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAturPerfDataEntry 1 } adslAturPerfLos OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAturPerfDataEntry 2 } adslAturPerfLpr OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAturPerfDataEntry 3 } adslAturPerfES OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 4 } -- general 15 min interval information -- adslAturPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAturInterval Table for which valid data has been stored. This value will be equal to the maximum number of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAturPerfDataEntry 5 } adslAturPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals which no valid data is available." ::= { adslAturPerfDataEntry 6 } -- 15 min current performance group -- adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturPerfDataEntry 7 } adslAturPerfCurr15MinLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAturPerfDataEntry 8 } adslAturPerfCurr15MinLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAturPerfDataEntry 9 } adslAturPerfCurr15MinLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAturPerfDataEntry 10 } adslAturPerfCurr15MinESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 11 } -- 1 Day current and previous performance group -- adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1Day interval." ::= { adslAturPerfDataEntry 12 } adslAturPerfCurr1DayLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 13 } adslAturPerfCurr1DayLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 14 } adslAturPerfCurr1DayLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 15 } adslAturPerfCurr1DayESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 16 } adslAturPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring data can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAturPerfDataEntry 17 } adslAturPerfPrev1DayLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1 day period." ::= { adslAturPerfDataEntry 18 } adslAturPerfPrev1DayLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1 day period." ::= { adslAturPerfDataEntry 19 } adslAturPerfPrev1DayLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1 day period." ::= { adslAturPerfDataEntry 20 } adslAturPerfPrev1DayESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1 day period. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 21 } adslAtucIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 8 } adslAtucIntervalEntry OBJECT-TYPE SYNTAX AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucIntervalNumber } ::= { adslAtucIntervalTable 1 } AdslAtucIntervalEntry ::= SEQUENCE { adslAtucIntervalNumber INTEGER, adslAtucIntervalLofs Gauge32, adslAtucIntervalLoss Gauge32, adslAtucIntervalLols Gauge32, adslAtucIntervalLprs Gauge32, adslAtucIntervalESs Gauge32, adslAtucIntervalValidData TruthValue } adslAtucIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAtucIntervalEntry 1 } adslAtucIntervalLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAtucIntervalEntry 2 } adslAtucIntervalLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAtucIntervalEntry 3 } adslAtucIntervalLols OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { adslAtucIntervalEntry 4 } adslAtucIntervalLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAtucIntervalEntry 5 } adslAtucIntervalESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAtucIntervalEntry 6 } adslAtucIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if there is valid data for this interval." ::= { adslAtucIntervalEntry 7 } adslAturIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 9 } adslAturIntervalEntry OBJECT-TYPE SYNTAX AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturIntervalNumber } ::= { adslAturIntervalTable 1 } AdslAturIntervalEntry ::= SEQUENCE { adslAturIntervalNumber INTEGER, adslAturIntervalLofs Gauge32, adslAturIntervalLoss Gauge32, adslAturIntervalLprs Gauge32, adslAturIntervalESs Gauge32, adslAturIntervalValidData TruthValue } adslAturIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAturIntervalEntry 1 } adslAturIntervalLofs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAturIntervalEntry 2 } adslAturIntervalLoss OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAturIntervalEntry 3 } adslAturIntervalLprs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAturIntervalEntry 4 } adslAturIntervalESs OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second paramter is a count of one-second intervals containing one or more crc anomolies, or one or more los or sef defects." ::= { adslAturIntervalEntry 5 } adslAturIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if there is valid data for this interval." ::= { adslAturIntervalEntry 6 } adslAtucChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 10 } adslAtucChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucChanPerfDataTable." INDEX { ifIndex } ::= { adslAtucChanPerfDataTable 1 } AdslAtucChanPerfDataEntry ::= SEQUENCE { adslAtucChanReceivedBlks Counter32, adslAtucChanTransmittedBlks Counter32, adslAtucChanCorrectedBlks Counter32, adslAtucChanUncorrectBlks Counter32, adslAtucChanPerfValidIntervals INTEGER, adslAtucChanPerfInvalidIntervals INTEGER, adslAtucChanPerfCurr15MinTimeElapsed INTEGER, adslAtucChanPerfCurr15MinReceivedBlks Gauge32, adslAtucChanPerfCurr15MinTransmittedBlks Gauge32, adslAtucChanPerfCurr15MinCorrectedBlks Gauge32, adslAtucChanPerfCurr15MinUncorrectBlks Gauge32, adslAtucChanPerfCurr1DayTimeElapsed INTEGER, adslAtucChanPerfCurr1DayReceivedBlks Gauge32, adslAtucChanPerfCurr1DayTransmittedBlks Gauge32, adslAtucChanPerfCurr1DayCorrectedBlks Gauge32, adslAtucChanPerfCurr1DayUncorrectBlks Gauge32, adslAtucChanPerfPrev1DayMoniSecs INTEGER, adslAtucChanPerfPrev1DayReceivedBlks Gauge32, adslAtucChanPerfPrev1DayTransmittedBlks Gauge32, adslAtucChanPerfPrev1DayCorrectedBlks Gauge32, adslAtucChanPerfPrev1DayUncorrectBlks Gauge32 } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAtucChanCrcBlockLength for more information. -- adslAtucChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 1 } adslAtucChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 2 } adslAtucChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAtucChanPerfDataEntry 3 } adslAtucChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAtucChanPerfDataEntry 4 } -- general 15 min interval information -- adslAtucChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAtucChanIntervalTable Table for which valid data has been stored. This value will be equal to the maximum number of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAtucChanPerfDataEntry 5 } adslAtucChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals which no valid data is available." ::= { adslAtucChanPerfDataEntry 6 } -- 15 min current performance group -- adslAtucChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAtucChanPerfDataEntry 7 } adslAtucChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 8 } adslAtucChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 9 } adslAtucChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 10 } adslAtucChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 11 } -- 1 Day current and previous performance group -- adslAtucChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1Day interval." ::= { adslAtucChanPerfDataEntry 12 } adslAtucChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 13 } adslAtucChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 14 } adslAtucChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 15 } adslAtucChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 16 } adslAtucChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAtucChanPerfDataEntry 17 } adslAtucChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1 day period." ::= { adslAtucChanPerfDataEntry 18 } adslAtucChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1 day period." ::= { adslAtucChanPerfDataEntry 19 } adslAtucChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1 day period." ::= { adslAtucChanPerfDataEntry 20 } adslAtucChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1 day period." ::= { adslAtucChanPerfDataEntry 21 } adslAturChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 11 } adslAturChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturChanPerfDataTable." INDEX { ifIndex } ::= { adslAturChanPerfDataTable 1 } AdslAturChanPerfDataEntry ::= SEQUENCE { adslAturChanReceivedBlks Counter32, adslAturChanTransmittedBlks Counter32, adslAturChanCorrectedBlks Counter32, adslAturChanUncorrectBlks Counter32, adslAturChanPerfValidIntervals INTEGER, adslAturChanPerfInvalidIntervals INTEGER, adslAturChanPerfCurr15MinTimeElapsed INTEGER, adslAturChanPerfCurr15MinReceivedBlks Gauge32, adslAturChanPerfCurr15MinTransmittedBlks Gauge32, adslAturChanPerfCurr15MinCorrectedBlks Gauge32, adslAturChanPerfCurr15MinUncorrectBlks Gauge32, adslAturChanPerfCurr1DayTimeElapsed INTEGER, adslAturChanPerfCurr1DayReceivedBlks Gauge32, adslAturChanPerfCurr1DayTransmittedBlks Gauge32, adslAturChanPerfCurr1DayCorrectedBlks Gauge32, adslAturChanPerfCurr1DayUncorrectBlks Gauge32, adslAturChanPerfPrev1DayMoniSecs INTEGER, adslAturChanPerfPrev1DayReceivedBlks Gauge32, adslAturChanPerfPrev1DayTransmittedBlks Gauge32, adslAturChanPerfPrev1DayCorrectedBlks Gauge32, adslAturChanPerfPrev1DayUncorrectBlks Gauge32 } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAturChanCrcBlockLength for more information. -- adslAturChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAturChanPerfDataEntry 1 } adslAturChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAturChanPerfDataEntry 2 } adslAturChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAturChanPerfDataEntry 3 } adslAturChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAturChanPerfDataEntry 4 } -- general 15 min interval information -- adslAturChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAturChanIntervalTable Table for which valid data has been stored. This value will be equal to the maximum number of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAturChanPerfDataEntry 5 } adslAturChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals which no valid data is available." ::= { adslAturChanPerfDataEntry 6 } -- 15 min current performance group -- adslAturChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturChanPerfDataEntry 7 } adslAturChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 8 } adslAturChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 9 } adslAturChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 10 } adslAturChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 11 } -- 1 Day current and previous performance group -- adslAturChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1Day interval." ::= { adslAturChanPerfDataEntry 12 } adslAturChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 13 } adslAturChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 14 } adslAturChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 15 } adslAturChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 16 } adslAturChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAturChanPerfDataEntry 17 } adslAturChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1 day period." ::= { adslAturChanPerfDataEntry 18 } adslAturChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1 day period." ::= { adslAturChanPerfDataEntry 19 } adslAturChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1 day period." ::= { adslAturChanPerfDataEntry 20 } adslAturChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1 day period." ::= { adslAturChanPerfDataEntry 21 } adslAtucChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 12 } adslAtucChanIntervalEntry OBJECT-TYPE SYNTAX AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucChanIntervalNumber } ::= { adslAtucChanIntervalTable 1 } AdslAtucChanIntervalEntry ::= SEQUENCE { adslAtucChanIntervalNumber INTEGER, adslAtucChanIntervalReceivedBlks Gauge32, adslAtucChanIntervalTransmittedBlks Gauge32, adslAtucChanIntervalCorrectedBlks Gauge32, adslAtucChanIntervalUncorrectBlks Gauge32, adslAtucChanIntervalValidData TruthValue } adslAtucChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAtucChanIntervalEntry 1 } adslAtucChanIntervalReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAtucChanIntervalEntry 2 } adslAtucChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAtucChanIntervalEntry 3 } adslAtucChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAtucChanIntervalEntry 4 } adslAtucChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAtucChanIntervalEntry 5 } adslAtucChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if there is valid data for this interval." ::= { adslAtucChanIntervalEntry 6 } adslAturChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 13 } adslAturChanIntervalEntry OBJECT-TYPE SYNTAX AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturChanIntervalNumber } ::= { adslAturChanIntervalTable 1 } AdslAturChanIntervalEntry ::= SEQUENCE { adslAturChanIntervalNumber INTEGER, adslAturChanIntervalReceivedBlks Gauge32, adslAturChanIntervalTransmittedBlks Gauge32, adslAturChanIntervalCorrectedBlks Gauge32, adslAturChanIntervalUncorrectBlks Gauge32, adslAturChanIntervalValidData TruthValue } adslAturChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAturChanIntervalEntry 1 } adslAturChanIntervalReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAturChanIntervalEntry 2 } adslAturChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAturChanIntervalEntry 3 } adslAturChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAturChanIntervalEntry 4 } adslAturChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAturChanIntervalEntry 5 } adslAturChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates if there is valid data for this interval." ::= { adslAturChanIntervalEntry 6 } -- Profile Group -- adslLineConfProfileIndexNext OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for adslLineConfProfileIndex when creating entries in the adslLineConfProfileTable. The value '0' indicates that no unassigned entries are available. To obtain the adslLineConfProfileIndexNext value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslMibObjects 14} adslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line." ::= { adslMibObjects 15} adslLineConfProfileEntry OBJECT-TYPE SYNTAX AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. A profile is created in one step with all necessary parameter values and adslLineProfileRowStatus set to createAndGo. This RowStatus object is also used to delete destroy profiles." INDEX { adslLineConfProfileIndex} ::= { adslLineConfProfileTable 1} AdslLineConfProfileEntry ::= SEQUENCE { adslLineConfProfileIndex AdslLineProfileType, adslAtucConfRateMode INTEGER, adslAtucConfRateChanRatio INTEGER, adslAtucConfTargetSnrMgn INTEGER, adslAtucConfMaxSnrMgn INTEGER, adslAtucConfMinSnrMgn INTEGER, adslAtucConfDownshiftSnrMgn INTEGER, adslAtucConfUpshiftSnrMgn INTEGER, adslAtucConfMinUpshiftTime INTEGER, adslAtucConfMinDownshiftTime INTEGER, adslAtucChanConfFastMinTxRate INTEGER, adslAtucChanConfInterleaveMinTxRate INTEGER, adslAtucChanConfFastMaxTxRate INTEGER, adslAtucChanConfInterleaveMaxTxRate INTEGER, adslAtucChanConfMaxInterleaveDelay INTEGER, adslAturConfRateMode INTEGER, adslAturConfRateChanRatio INTEGER, adslAturConfTargetSnrMgn INTEGER, adslAturConfMaxSnrMgn INTEGER, adslAturConfMinSnrMgn INTEGER, adslAturConfDownshiftSnrMgn INTEGER, adslAturConfUpshiftSnrMgn INTEGER, adslAturConfMinUpshiftTime INTEGER, adslAturConfMinDownshiftTime INTEGER, adslAturChanConfFastMinTxRate INTEGER, adslAturChanConfInterleaveMinTxRate INTEGER, adslAturChanConfFastMaxTxRate INTEGER, adslAturChanConfInterleaveMaxTxRate INTEGER, adslAturChanConfMaxInterleaveDelay INTEGER, adslLineConfProfileRowStatus RowStatus } adslLineConfProfileIndex OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line configuration table in order to identify a row of this table" ::= { adslLineConfProfileEntry 1 } adslAtucConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaption adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time (i.e., RADSL) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See WT008 for more information." ::= { adslLineConfProfileEntry 2 } adslAtucConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAtucConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 3 } adslAtucConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 4 } adslAtucConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 5 } adslAtucConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 6 } adslAtucConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 7 } adslAtucConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 8 } adslAtucConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 9 } adslAtucConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 10 } adslAtucChanConfFastMinTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 11 } adslAtucChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates." ::= { adslLineConfProfileEntry 12 } adslAtucChanConfFastMaxTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 13 } adslAtucChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 14 } adslAtucChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel per ANSI T1.413, == (S-factor x d) ------------- 4 milli-seconds, where 'd' is the Interleaving Depth. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 15 } adslAturConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaption adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time (i.e., RADSL) } MAX-ACCESS read-write STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 for more information." ::= { adslLineConfProfileEntry 16 } adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(1..100) UNITS "%" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 } adslAturConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 18 } adslAturConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 19 } adslAturConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 20 } adslAturConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 21 } adslAturConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 22 } adslAturConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 23 } adslAturConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 24 } adslAturChanConfFastMinTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 25 } adslAturChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 26 } adslAturChanConfFastMaxTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 27 } adslAturChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX INTEGER(1..32000) UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 28 } adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel per ANSI T1.413, == (S-factor x d) ------------- 4 milli-seconds, where 'd' is the Interleaving Depth. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 } adslLineConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslLineConfProfileEntry 30 } adslLineAlarmConfProfileIndexNext OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for adslLineAlarmConfProfileIndex when creating entries in the adslLineAlarmConfTable. The value '0' indicates that no unassigned entries are available. To obtain the adslLineAlarmConfProfileIndexNext value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslMibObjects 16} adslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line" ::= { adslMibObjects 17} adslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. A profile is created in one step with all necessary parameter values and adslLineAlarmConfProfileRowStatus set to createAndGo. This RowStatus object is also used to delete destroy profiles." INDEX { adslLineAlarmConfProfileIndex} ::= { adslLineAlarmConfProfileTable 1} AdslLineAlarmConfProfileEntry ::= SEQUENCE { adslLineAlarmConfProfileIndex AdslLineProfileType, adslAtucThresh15MinLofs INTEGER, adslAtucThresh15MinLoss INTEGER, adslAtucThresh15MinLprs INTEGER, adslAtucThresh15MinESs INTEGER, adslAtucThreshFastRateUp Integer32, adslAtucThreshInterleaveRateUp Integer32, adslAtucThreshFastRateDown Integer32, adslAtucThreshInterleaveRateDown Integer32, adslAtucInitFailureTrapEnable INTEGER, adslAturThresh15MinLofs INTEGER, adslAturThresh15MinLoss INTEGER, adslAturThresh15MinLprs INTEGER, adslAturThresh15MinESs INTEGER, adslAturThreshFastRateUp Integer32, adslAturThreshInterleaveRateUp Integer32, adslAturThreshFastRateDown Integer32, adslAturThreshInterleaveRateDown Integer32, adslLineAlarmConfProfileRowStatus RowStatus } adslLineAlarmConfProfileIndex OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line alarm configuration table in order to identify a row of this table" ::= { adslLineAlarmConfProfileEntry 1} adslAtucThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Frame Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 2} adslAtucThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Signal Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 3} adslAtucThresh15MinLols OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Link Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 4} adslAtucThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Power Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 5} adslAtucThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Errored Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 6} adslAtucThreshFastRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 7} adslAtucThreshInterleaveRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 8} adslAtucThreshFastRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 9 } adslAtucThreshInterleaveRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 10 } adslAtucInitFailureTrapEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enables and disables the InitFailureTrap. This object is defaulted disable(2)." DEFVAL { disable } ::= { adslLineAlarmConfProfileEntry 11 } adslAturThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Frame Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 12 } adslAturThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Signal Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 13 } adslAturThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Loss of Power Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 14 } adslAturThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of Errored Seconds, encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 15 } adslAturThreshFastRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 16 } adslAturThreshInterleaveRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Interleave' channels only. configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 17 } adslAturThreshFastRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 18 } adslAturThreshInterleaveRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-write STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 19 } adslLineAlarmConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has choosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchName upon SNMP request." ::= { adslLineAlarmConfProfileEntry 20 } -- Line Code Specific Tables adslAtucLCSTable OBJECT IDENTIFIER ::= { adslMibObjects 18 } -- These are place holders for the Line Code Specific MIBs -- once they become available. adslAturLCSTable OBJECT IDENTIFIER ::= { adslMibObjects 19 } -- These are place holders for the Line Code Specific MIBs -- once they become available. adslConformance OBJECT IDENTIFIER ::= { adslLineMib 2 } adslGroups OBJECT IDENTIFIER ::= { adslConformance 1 } adslCompliances OBJECT IDENTIFIER ::= { adslConformance 2 } adslTraps OBJECT IDENTIFIER ::= { adslLineMib 3 } adslAtucTraps OBJECT IDENTIFIER ::= { adslTraps 1 } adslAtucPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 1 } adslAtucPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 2 } adslAtucPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 3 } adslAtucPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 4 } adslAtucRateChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate } STATUS current DESCRIPTION "The ATUCs transmit rate has changed (RADSL mode only)" ::= { adslAtucTraps 0 5 } adslAtucPerfLolsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 6 } adslAtucInitFailureTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucCurrStatus } STATUS current DESCRIPTION "ATUC initialization failed. See adslAtucCurrStatus for potential reasons." ::= { adslAtucTraps 0 7 } adslAturTraps OBJECT IDENTIFIER ::= { adslTraps 2 } adslAturPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold exceeded" ::= { adslAturTraps 0 1 } adslAturPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold exceeded" ::= { adslAturTraps 0 2 } adslAturPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold exceeded" ::= { adslAturTraps 0 3 } adslAturPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold exceeded" ::= { adslAturTraps 0 4 } adslAturRateChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, adslAturChanCurrTxRate, adslAturChanPrevTxRate } STATUS current DESCRIPTION "The ATURs transmit rate has changed (RADSL mode only)" ::= { adslAturTraps 0 5 } -- no adslAturPerfLolsThreshTrap possible { 6 } -- no adslAturInitFailureTrap possible { 7 } -- these are defined for use as ifTestTypes (see RFC1573) -- additional vendor-specific tests are easily supported -- (just define in vendor MIB) -- adslTestTypes OBJECT-TYPE SYNTAX INTEGER { atucSelfTest (1), aturSelfTest (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "values as above" ::= { adslLineMib 4 } adslTestCodes OBJECT IDENTIFIER ::= { adslLineMib 5 } END -- -- ADSL Forum TR-006 V1.0 -- Attachment I - ASN.1 MIB SNMP-based ADSL Line MIB -- -- Page 34 March 1998